1. A stable x (n) input signal to a LTI system with a unit impulse response h (n) = 28 (n) +(1/2) n u (n)applving and y (n) = 2 (1/4) nThe u (n) output is obtained.]%3Da) Find the frequency response of the system.b)Find the x (n) sign and spectrum applied to the input with DTFT.c)Give the input / output difference equation of the system.

Given: A unit impulse response of an LTI system is given by hn=2δn+12nun.

1. A stable x (n) input signal to a LTI system with a unit impulse response h (n) = 26 (n) + (1/2) n u (n) applving and y (n) = 2 (1/4) n The u (n) output is obtained] a) Find the frequency response of the system. b) Find the x (n) sign and spectrum applied to the input with DTFT. c) Give the input / output difference equation of the system.

1. A stable x (n) input signal to a LTI system with a unit impulse response h (n) = 26 (n) + (1/2) n u (n) applving and y (n) = 2 (1/4) n The u (n) output is obtained] a) Find the frequency response of the system. b) Find the x (n) sign and spectrum applied to the input with DTFT. c) Give the input / output difference equation of the system.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. A 70 year old man was taken to hospital due to chest pain the doctors immediately took him to ICU and did the ECG. The ECG signal is analyzed on spectrum analyzer to find the problem. Assuming that spectrum analyzer internally contains DSP system to do the given task. The ECG signal taken from the patient has bandwidth of 70Hz in that the required signal bandwidth is only 60Hz remaining part of the signal represent the noise. Design a DSP system that accepts only the required signal and samples it and the sampled spectrum contains 40Hz separation between neighboring spectral components and this discrete time signal is transformed into frequency domain using 16 point DFT find the following.i. Find the cutoff frequency of the antialiasing filterii. Find the sampling frequency of the sampler usediii. Find the Frequency of X(4) and X(8) iv. Draw the block diagram of the designed system
We have a biomedical measurement set-up that can be modeled as a second order system with natural resonance frequency 15.9 Hz, damping coefficient 0.707 and gain 10.a. Determine the transfer function of the system.b. Determine the differential equation representing the system.c. Design the system in block diagram form using integrators, constant multipliers, and summing junction.d. Determine the step response of the system and draw it showing all important amplitude and time values on the plot.
The Nyquist sampling rate for a low pass signal of bandwidth B Hz is defined as 2B. If we are to avoid aliasing when sampling such a signal, we would need to sample at: Select one: O Greater than the Nyquist rate O Less than the Nyquist rate O At least twice the Nyquist rate O At least half the Nyquist rate O Exactly at the Nyquist rate A low-pass analogue signal has a bandwidth of 15 kHz and has a SNR of 43 dB due to thermal noise and interference from nearby electrical equipment. If uniform 10-bit quantisation is used when sampling and digitising the signal, which of the following would you expect to be the output digital bit rate? Select one: O 100 kbit/s O 75 kbit/s O 150 kbit/s O 30 kbit/s O 330 kbit/s
Given the following Two-stage Operational Transconductance Amplifier and its corresponding specifications: VDD Vout1 kp kn vth,n vth,p λη λp 3 5 1.5 0.75 1.13E-03 2.25E-03 0.28 0.3 0.6 0.3 |Id(M4)| 1.00E-05 Vsd4 0.55 Vds2 0.3 a) Assuming Vout2 = 0.75V, determine the the drain current of M5 and the gate voltage, V₁, of M6 b) Draw the small signal equivalent model of the circuit c) Calculate for the transconductance and output resistance of the highlighted (in red) portion of the circuit Vc Vb Va Vi VDD P PMOS M4 PMOS M3 M2 NMOS M1 NMOS Vout1 Vd JU PMOS M5 M6 NMOS Vout2
Find the transfer function Hp(s) (for the first order system)of the circuit shown in Figure and determine its theoretical gain (K) and time constant (τ).
please matlab using
For the digital system shown in below: 1) Write down the difference equation that represents the system. 2) Find the transfer function of the system, i.e. H(Z) x(n) y(n) 0.75 0. 125 Delay one sample Delay one sample
Given a discrete-time signal x[n] as shown in Figure Q1. Analyse the properties of the signal by considering the following: (1) Determine the magnitude of x[-3], 2x[3] + 2x[0] and x[-4] - 3x[2]. (ii) Extract the expression of the signal x[n] in terms of unit sample sequence delta [n] and Its scaled and shifted version. (ii) Calculate the power of the signal x[n]. x[n] -2 -1 Figure Q1
6 - Forward path transfer function is applied to the input of a negative unit feedback system given as below, and the overrun rate at the output of the system is given as% OS = 5.4%. K G(s) = s(s +1) In this case, what is the damping rate of the system? A) 0.63 B) 0.57 C) 0.61 D) 0.68 E) 0.55
A system that satisfies the properties of superposition and homogeneity. Select one: a. Transfer function b. Linear c. Super position d. Signal flow e. Non linear W
S2) Discrete signal x[n] is given by the following graph. Plot the filtered output signal y[n] when a causal two point moving average filter x[n]. ((x[n-1]+ x[n])/2) is applied to 5 3 ... 1 2 -1 0 1 2 3 4 3 6
Please answer all subpart either dislike is ready please all subpart is compulsory please..