1. A square metal plate 0.180 m on each side is pivoted about an axis through point o at its center and perpendicular to the plate. Calculate the net torque about this axis due to the thee forces shown in the figure if the magnitudes of the forces are F, = 18.0 N, F2 = 26.0 N, F3 = 14.0 N. The plate and all forces are in the plane of the page. F2 F1 0.180 m 45° F3 0.180 m

1. A square metal plate 0.180 m on each side is pivoted about an axis through point o at its center and perpendicular to the plate. Calculate the net torque about this axis due to the thee forces shown in the figure if the magnitudes of the forces are F, = 18.0 N, F2 = 26.0 N, F3 = 14.0 N. The plate and all forces are in the plane of the page. F2 F1 0.180 m 45° F3 0.180 m

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

1.0m 3.0m 0.5m mi m2 m, PA N, 5. The drawing above shows two objects on a board supported at two locations. The m = 40 kg (centered over P), m;=20 kg and m3=10 kg. b. Determine the magnitude of the torque exerted about point P by .. (don't forget to convert masses to forces.) i. mi ii. m2 ii. m3
The fishing pole in the figure below makes an angle of 20.0° with the horizontal. What is the magnitude of the torque exerted by the fish about an axis perpendicular to the page and passing through the angler's hand if the fish pulls on the fishing line with a force F = 115 N at an angle 37.0° below the horizontal? The force is applied at a point L = 2.20 m from the angler's hands. N.m 20.0° 20.0⁰ 37.0° F
Wolverine has an arm that is 1[m] long and claws that are 0.5[m] long. He's trying to knock over a wall. His shoulder can exert a torque of 1,500[N-m]. What is the ratio of force on the wall with vs without his claws extended? 1.5[m] point Pivot F /F Adamantium Wall without with claws claws A. 2/3 F Wolverine with В. 3/2 with claws С. 1 1.0[m] Pivot Adamantium D. I don't know but the torque direction is point Wall E. I don't know but the torque direction is Fwithout Wolverine Bare hands
+, F. You use a wrench to turn a rusty nut. You place your hand at where the black dot is and apply a force F = 110N at an angle 0 = 59 degrees. The distance from your hand to the center of nut d = 30 cm. Calculate the torque in N. m your hand applies. %3D %3D %3D p. 0. MacBook Pro G Search or type URL
In this problem you have to draw the free body diagram. Please be sure, don't use chatgpt.
FA740.0N FI-10.0N TO-3 A rotor has four forces applied to it as shown to the right. Find the magnitude and sign of the net (total) torque (about the center of the rotor) on the rotor due to these four forces. Force F4 is applied at the center of the rotor. F3-30ON F220.0N 5.00cm 10.0cm 5.00cm hp
The fishing pole in the figure below makes an angle of 20.0° with the horizontal. What is the magnitude of the torque exerted by the fish about an axis perpendicular to the page and passing through the angler's hand if the fish pulls on the fishing line with a force F = 125 N at an angle 37.0° below the horizontal? The force is applied at à point L = 1.92 m from the angler's hands. N.m -I 20.0° 37.0 1 20.0° F
a. What is the maximum torque applied by the cable? (Give your answer in N m.) b. What is the torque due to the weight of the bridge? (Give your answer in N m.) c. How far can Lancelot ride out along the bridge before the cable breaks? (Give your answer in m.) Note: At his maximum distance, the torque from the cable will equal the torque from both the weight of the bridge and the weight of Lancelot.
A. Find the required F to achieve Net Torque = 0. Assume b = 2a. B. After a design modification, all forces including F stay the same. If new design is basedon b = 1.5a, what will be the net torque after modifications?
5. A force of 292 N is exerted on the end of a wrench in order to apply a torque of 37.4 N·m to a bolt head. The point of application of the force is 21.5 cm from the center of the bolt. What angle does the force make with respect to the wrench handle?
Inigo and Fezzik push with perpendicular forces on a heavy door with width R. Inigo pushes with force F at 3R/4 from the hinge, while Fezzik pushes with force 2F at R/3 from the hinge. Which of the following descriptions is correct? (diagram shows the top-down view) hinge O B ОА A. Inigo (pushing with F) exerts a greater a torque on the door. B. Fezzik (pushing with 2F) exerts a greater a torque on the door. C. The torques they exert are equal in magnitude. D. There is zero net torque on the door. OD 3R/4 O C R/3 2F
Practice Problems: Torque Physics 1. A 200 g mass is placed on the meter stick 20 cm from the fulcrum. An unknown mass is positioned 8 cm from the fulcrum to balance the system. What is the mass of this unknown object? Unknown mass T = rx F Page rccw Fulcrum rcw 2. A 250 g mass is placed on the meter stick 30 cm from the fulcrum. An unknown mass is positioned 40 cm from the fulcrum to place the system in equilibrium. What is the mass of the unknown object? 1 / 2 Load: 200-g mass +