1. A simply supported beam of length 6 m carrying point loads of 4 kN, and 8 kN at 1 mand 4.5 m respectively from the right support and point loads of 2 kN and 6 kN acts at 2.5 m and 3.5 m from the left support. Construct the shear force and bending moment diagram for the beam and also identify the point at which the maximum shear force and bending moment is acting on the beam

1. A simply supported beam of length 6 m carrying point loads of 4 kN, and 8 kN at 1 mand 4.5 m respectively from the right support and point loads of 2 kN and 6 kN acts at 2.5 m and 3.5 m from the left support. Construct the shear force and bending moment diagram for the beam and also identify the point at which the maximum shear force and bending moment is acting on the beam

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please box the final answer. Thank you
The truck is moving along a 20 m span of beam. The front axle is 30 kN, the middle is 75 kN and the rear is 45 kN. The middle load is space 4m from the front and 8 m from the rear. a. Determine the moment under each axle. b. Calculate the maximum moment produced by the load. c. Calculate the maximum shear. 45 KN 75 kN 30 kN 8 m A 20 m 2 4 m B M
7
(b) The gudgeon pin is used to connect the piston and the connecting rod. Show from first principles that the maximum bending moment acting on the gudgeon pin is given by: PL M = 8 where P is the maximum gas load and L is the length of the pin
i need the answer quickly
Determine the reactions at supports and then draw the shear force and bending moment diagrams for the beam shown below and determine the size of the beam if it has a rectangular cross section where the height is 3 times the width. Allowable bending stress is 80 MPa. 8 kN 3000 15 kNm 3 kN/m 2000 Width Height (3 x width) Section through beam
Determine the transverse force and moment diagram for the beam above that is loaded as shown in the figure. Location and value for maximum moment in field between supports must be calculated exactly.
Calculate the internal shear forces and the value of bending moments at points A, D (on member DB and member AD), and B. Origin C 2 m D 2.5 m 250 mm 125 mm 1.5 m 50 mm ( 25 kN /m B 4m - 2 m-
Draw the shearing-force and bending-moment diagrams for the following beams: A cantilever of length 20 m carrying a load of 10 kN at a distance of 15 m from the supported end. A cantilever of length 20 m carrying a load of 10 kN uniformly distributed over the inner 15 m of its length. A cantilever of length 12 m carrying a load of 8 kN, applied 5 m from the supported end, and a load of 2kN/m over its whole length.
Q1/ A beam of uniform section with rigidly fixed ends which are at the same level has an effective span of 10 m. It carries loads of 30 kN and 50 kN at 3 m and 6 m respectively from the left-hand end. Find the vertical reactions and the fixing moments at each end of the beam. Determine the bending moments at the two points of loading.
The cantilever beam carries a uniformly varying load as shown. In addition, a 1000 lb-upwardvertical load acts at the free end of the beam. Derive the shear force and bending momentequations and draw the shear force and bending moment diagrams. Neglect the weight of thebeam
Beam with a pin support at point A,roller support at pint B and the acting forces can be seen below. Determine the internal forces and moments at the mid point of BC section. (20 Points) 6 m 12 kN/m B 3 m 6 kN