1. A pump must be selected to deliver water to a tank that is 9m above a sump. The system to which the pump will be connected consists of a pipe 100m long and 100mm diameter with an f value of 0.006. Determine the pump that will require the least energy per unit volume in J/m³ to deliver water to the tank. (19mks) Q (m³/s) 0 0.01 0.015 0.02 0.025 0.03 Ha (m) 22.6 20.8 19.1 16.7 13.5 9.6 na (%) 0 59 72 80 79 74 13.2 12.7 12.1 11.4 10.4 9 Hb (m) пь (%) 0 42 60 74 80 77

1. A pump must be selected to deliver water to a tank that is 9m above a sump. The system to which the pump will be connected consists of a pipe 100m long and 100mm diameter with an f value of 0.006. Determine the pump that will require the least energy per unit volume in J/m³ to deliver water to the tank. (19mks) Q (m³/s) 0 0.01 0.015 0.02 0.025 0.03 Ha (m) 22.6 20.8 19.1 16.7 13.5 9.6 na (%) 0 59 72 80 79 74 13.2 12.7 12.1 11.4 10.4 9 Hb (m) пь (%) 0 42 60 74 80 77

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SHOW THE SOLUTION. WHY THE ANSWER BECAME -2.72 J/N. SHOW CORRECT FIGURE.
Fluid mechanics
Problem 5 The system curve follows the equation: hp = 115.2 + 0.086Q², in which the pump head is in ft, and the discharge is in GPM. The system operates to deliver water (10°C) at 100 GPM. After 10 hours, the electrical energy consumption for operating the pump is 20 kWh. What is most approximately the pump efficiency during this period?
1. The velocity of water is 8 m/s and the pressure is 140 kPa on the discharge side of a pump. a. What is the head of the pump if the velocity is 4 m/s and the pressure is 90 kPa on the suction side of the pump? b. How much power is required to drive it if the diameter of the suction side is 600 mm? c. If the pump is rated at 120 hp, what is the efficiency of the pump neglecting energy losses in the system? Pj=90 kPa P>=140 kPa Vj=4m/s ♡ Vz=8m/s Suction side Discharge side 600 mum
a circular orifice is located 5m below the water surface. if the tank is large and the diameter of the orifice is 5mm, calculate the discharge in cubic meters oer second if the coefficient of discharge is 0.60. a. 0.00012 b. 0.00812 c. 0.00140 d. none
Pls help me
10.87 What power must be supplied by the pump to the flow if water (T = 20°C) is pumped through the 300 mm steel pipe from the lower tank to the upper one at a rate of 0.314 m³/s? Elevation = 235 m 10 m 50 m Elevation = 200 m 300 mm r= 300 mm 100 m
A closed tank contains 20 m deep water. A hose is connected as shown such that the nozzle (diameter = 1cm) is directed straight up. If the air gage pressure inside the tank is 200kPa, solve the theoretical volumetric flowrate out of the nozzle assuming no losses. AIR 20 m O 0.0020m^3/s O 0.0022m^3/s O 0.0031m^3/s O 0.0027m^3/s
3. The horizontal pump in the Figure discharges 18°C water at 35 m/h. Neglecting losses, what power in kW is delivered to the water by the pump? y = 9790 N /m3 160 kP 480 kPa Pump De13 em Dzes em
Where did this 101.3 over 76 coming from? Its not on the given. Here is the picture.
B1
The following figure and table contains the water levels of the reservoirs in the system and the properties of the pipes.Calculate the current values in the pipes ignoring the local head losses (ν = 10-6 m.2nd/s). Energy slope linedraw