1. A piston rod of an air-operated press is to exert a maximum force of 20 kN. During the application of this force, the air cylinder pressure was maintained at 700 kPa. Assuming that the piston rod length is 760 mm with its right hand end pin connected to the operating lever and the piston end is fixed end, find: a. The diameter of the rod for a safety factor of 2.5. Sy = 250 MPa; E = 200 GPa. b. The diameter of the piston rod, if piston packing friction is 10% of the maximum force.

Q: please solve and explain using values below

A: Detailed step by step solution is given below, still if you have any query please feel free to…

Q: (1) A B

A: for solution refer below images.

Q: The load is figure below of 1910 lb is to be supported by the two vertical steel wires for which…

A: Consider the free body diagram for the load as shown below.

Q: 6. A carbon steel ball (E-30x10" psi, v=0.29) with a radius of 3-in is pressed together with an…

A:

Q: The frame shown is fitted with three 28 cm diameter frictionless pulleys. A force of F' = 640 N is…

A:

Q: 2. In the following truss structure, the angles of A and B are 6A = 120° and B = 30°, respectively.…

A: Given:Yield stress, The factor of safety, The length of the member AB

Q: A rod as shown below is subjected to a tensile force F = 1.1 kN acting at the centroid of two faces.…

A: As the rod is subjected to tensile force, there will be tensile stress on the rod. Tensile stress…

Q: 2. The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A…

A:

Q: An L-shaped bracket is supported by a frictionless pin at A and a cable between points B and D. If…

A:

Q: 1. A rod of length 1.50 m and diameter 0.12 m is mounted in a rigid wall A vertical bar of length…

A: INTRODUCTION : In order to solve the above problem, the maximum shear stress theory is applied when…

Q: The push rods on the suspension of the Pitt Formula SAE race car are Chome-moly steel (E = 29,000…

A: The elastic modulus is .The yield stress is .The length of rod is .The outside diameter is .The wall…

Q: MECHANICS OF DEFORMABLE BODIES 1. In the figure shown, the rigid bar with negligible mass was…

A:

Q: An A-992 steel wire is connected at ends B and C With an initial diameter of 15 mm. The weight of…

A:

Q: The truss below is subject to the loads as shown. All of the members are attached at plates and can…

A: The normal force in member AE.Given:The applied loads are .The given truss is shown below.

Q: Compound axial member ABC has a uniform diameter of d = 1.0 in. Segment (1) is an aluminum [E1 =…

A:

Q: A solid 0.6-in.-diameter cold-rolled steel rod is pinned to fixed supports at A and B. The length of…

A:

Q: 1.5 m 3 m 400 N 200 N 1 m Member AB is supported by a cable BC and at A by a square rod which fits…

A: Given data: F1=200 NF2=400 NuBC=-0.857i+0.429j+0.286k Need to determine the tension in the cable.

Q: Currently eighty-five percent of all neck injuries are caused by rear-end car collisions. To…

A:

Q: An industrial machine requires a solid, round piston connecting rod 200 mm long, between pin ends…

A: Length le= 200 mm Force F = 80,000 Nfactor of safety = 2.5 Sy = 496 MPa E = 71 GPa.

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.