1. A force of 250 kN at 25° is combined with a force of 180 kN at 100°. What is the resultant force in kN? A. 362.23 C. 356.58 B. 324.56 19:30 20 D. 343.79 WOUR 201 911 2. A hanger is to support a 1340-kg object. If the ultimate tensile strength of the rod is 350 MPa and a factor of safety of 3 is to be used, what rod diameter is required? A. 10 mm C. 11 mm ES B. 13 mm D. 12 mm

1. A force of 250 kN at 25° is combined with a force of 180 kN at 100°. What is the resultant force in kN? A. 362.23 C. 356.58 B. 324.56 19:30 20 D. 343.79 WOUR 201 911 2. A hanger is to support a 1340-kg object. If the ultimate tensile strength of the rod is 350 MPa and a factor of safety of 3 is to be used, what rod diameter is required? A. 10 mm C. 11 mm ES B. 13 mm D. 12 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

please answer the 3 problems
Identical steel bars are used to support a 7400-N load as shown. For the properties of steel bar: A = 500 mm², α = 11.7 x 10-6 m/ (m°C ), and E = 200 GPa. Determine the load exerted by steel bars A and B after a temperature increase of 72 °C. Also, calculate the total elongation sustained by bars A and B. 0.80 m Į 18 18 7400 N
Given is the 200mm X 400 mm rectangular beam below. 9 kN 7.50 kN/m 400 mm 1.50 kNm A C 1.50m 7.50m 200 mm R1 R2 Figure 1 What is the moment of inertiaof the beam section in mm4?
Question 3 of 15 2.5/5 : Two rods and one cable are attached to the supports at O. If two of the forces are as shown, determine the magnitude F and direction of the third force so that the resultant of the three forces is vertically downward with a magnitude of 1200 lb. F 800 lb 300 lb Answers: i A - FULL HD- 49° 21° 0 Type here to search. 1080 lb O O BI .c O acer 30°C Heavy t-storms Ques Questi Numeric Blank with Questio Numeric Fi Blank with Viewing Question Numeric Fill Blank with Ur Question 4 Numeric Fill in Blank with Unit Question 5
help me please
Engineering Mechanics. Please help to solve the problem below.
The tongs are used to lift the 150-kg crate, whose center of mass is at G. Determine which Free Body Diagram can be used to find the least coefficient of static friction at the pivot blocks so that the crate can be lifted. 500 mm 500 mm 275 mm LOS E 300 A H B
2.13 The resultant of three tensions in the guy wires anchored at the top of the tower is vertical. Find the un- known but equal tensions T in the two wires. All three wires and the tower are in the same vertical plane. mom x won goalsq sr 11 JAG BESHI BRIGH AGU Figure 2.52
Solve the support reactions of the following beams. Write the complete solution, each question on clean paper. Thanks again for helping me.
SITUATION I: A 50-m steel tape is of standard length under a pull of 5kg and a temperature of 22 degree celcius when supported throughout its entire length. The tape weighs 0.06 kg/m, has a cross section area of 0.06 cm'and a modulus of elasticity of 2x10°kg/cm?. The tape was used in the field to measure a distance that was determined to be 525.48. At the time the measurement was made, the constant pull applied was 10kg with the tape supported only at endpoints. During measurement, the temperature was observed to be at an average of 19 degree Celsius. Use alpha a= 12.36x10/degree celcius. 1. Determine the correction due to tension. a. 0.021898 m b. 0.021895 m c. 0.021911 m d. 0.021589 m 2. Determine the correction due to temperature. a. 0.01984 m b. 0.01968 m c. 0.01986 m d. 0.01948 m 3. Determine the correction due to sag. а. 1.8998 m b. 1.8898 m c. 1.8888 m d. 1.9898 m 4. Find the corrected length of the line a. 523.5826 m b. 524.5823 m c. 525.6832 m d. 526.3628 m
M ähäi 30 Q4: The top of the 60 lb ladder has a small roller, and at the ground the coefficient of static friction is 0.35. The distance X to which the 160 lb painter can climb without causing the ladder to slip at its lower end A * is B 2 ft Us =0.35 A 8 98 ft 20 ft
Two spheres, each 1.20 m in diameter, weighs 4 kN and 12 kN respectively. They are connected with a short rope and palced in water. Find the tension in the rope in kN. CHOICES: a.2.15 b.3.12 c.3.87 d.4.45