Please answer the problems completely. Show the full solution. 1. A farmer applies nitrogen to a crop from a tank pressurized to 1000 kPa absolute at a temperatureof 25-C. What minimum temperature can be expected in the nitrogen if it is released to theatmosphere?Answer: -119°C (Use: k-1.4)2. A lin diameter soap bubble has an internal pressure 0.0045 lb/in? greater than that of the outsideatmosphere. Compute the surface tension of the soap-air interface. Note that a soap bubble has twointerfaces with air, an inner and outer surface of nearly the same radius.Answer: 0.00675 lb/ft

Given Data Nitrogen gas with 1000 kPa pressure and 25°C temperature

Answered: 1. A farmer applies nitrogen to a crop…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need answer within 5 minutes please please with my best wishes
Can you give me an example of laying out compound curves, please include explanation for each process/procedure of the solving.
Statics of Rigid Bodies Note: If you have already answered the problems in this post, kindly ignore it. If not, then answer it. Thank you, Tutor! Content Covered: - Method of Joints Direction: Create two problems based on the topic "Method of Joints" and then solve them with a complete solution. In return, I will give you a good rating. Thank you so much! Note: Please bear in mind to create two problems based on the topic "Method of Joints." Be careful with the calculations in the problem. Kindly double check the solution and answer if there is a deficiency. And also, box the final answer. Thank you so much!
PLEASE WRITE LEGIBLY, COMPLETE SOLUTIONS WITH DRAWING THANK YOU! A car weighing 9 kN travels at 80 km/hr. At the foot of an incline of 10%, the engine stops. Determine: a – acceleration. b – time for the car before it stops. c – distance traveled by the car before it stops.
A Brinell test is performed on a steel using a 1.2 in. diameter indenter with a load of 71825 Ibs. A 0.75 in. Determine in indentation was measured on the surface of the steel. Determine: a) HBN (psi); b) tensile strength (psi) a) HBN = psi b) Tensile strength = psi
where did you get value of Ws, the 572.116, the 0.9608, and 0.3350? you just copied the entire solution from internet
Please give a steps by steps explanation of each question answer please. Thanks you so much
|Read the problem statement and the solution provided. There may or may not be one or more mistakes in the solution. Go through the solution carefully and then do the following. 1. State if the solution is correct or incorrect 2. If the solution is incorrect, identify what is the mistake in the solution. Be specific and succinct. 3. If the solution is incorrect, provide the final solution with appropriate steps. You can make the corrections directly on a copy of this provided solution, but make sure you clearly explain the corrections. Problem: Consider fully-developed flow of water through a 24-cm diameter tube. The water comes in at 20°C and exits at 40°C. The surface temperature of the tube is uniform at 60°C. The water flow has a mass flow rate of 0.24 kg/s. What is the average convection coefficient of the water flow? Solution: We have T, = 60°C, Tmi = 20°C, Tmo = 40°C, So, the bulk-mean temperature is Tm = 30°C. The appropriate properties are: u = 7.98 × 10-4 kg/ms; k = 0.615…
State one word problem and solve it wherein the ideal mechanical advantage of a wedge is being solved. Use the formula, IMA = (Length of the Widge) divided by (Width of the Wedge). note: please do not forget to include your solution in solving the problem.
i need clear ans and solve very very fast in 20 min and thank you | DYBALA A part under forming force showed that 15% decrease in thickness and 10% increase in width, find the change in length (sign and value) if initial length is 200 mm?
In the last few steps, where did 0.4 come from?
help num3 please,badly need ittt

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS