1. A crowbar lifts a weight in Fig. 10-21 below. A downward force on the long end of the crowbar, F₁, equals 225 N. How much weight must be held up by the upward force, F2, being exerted by the short end? The value of r₁-perpendicular is equal to 0.300 m and that of r₂-perpendicular is 0.0500 m. Ans. 1350 N upward.

1. A crowbar lifts a weight in Fig. 10-21 below. A downward force on the long end of the crowbar, F₁, equals 225 N. How much weight must be held up by the upward force, F2, being exerted by the short end? The value of r₁-perpendicular is equal to 0.300 m and that of r₂-perpendicular is 0.0500 m. Ans. 1350 N upward.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

2. A scaffold of mass 60 kg and length 5.0 m is supported in a horizontal position by a vertical cable at each end. A window washer of mass 80 kg stands at a point 1.5 m from one end. What is the tension in (a) the nearer cable and (b) the farther cable?
2. The horizontal beam in Fig. 1 weighs 150 N, and its center of gravity is at its center. Find (a) the tension in the cable and (b) the horizontal and vertical components of the force exerted on the beam at the wall.
Q18
A horizontal 4.0 m long 5.0 N uniform bar at one end is attached to a wall by a frictionless hinge; and at the middle of the bar there is a vertical cable pulling down 7.0 N, and at the middle of the bar there is also a cable that is at 45 ° to the horizontal pulling up as shown. ii) What is the magnitude of the horizontal component of the force on the bar due to the hinge?
Please answer fast
Determine the force in member BE of the loaded truss. The force is positive if in tension, negative if in compression. D 5 KN 8 KN 2 KN 2 m 2 m B 2 m A Answer: BE = i E -4 m F kN
6. A 5-meter long wire has a total mass of 0.65 kg. It is suspended by two uniform 200-N poles, which lean apart from each other, as shown below. Assume the only significant forces are the tension of the wire, the gravity of the earth, and a contact force with the ground below. 6. A 5-meter long wire has a total mass of 0.65 kg. It is suspended by two uniform 200-N poles, which lean apart from each other, as shown below. Assume the only significant forces are the tension of the wire, the gravity of the earth, and a contact force with the ground below. wire 60° 60° Calculate the velocity of a transverse wave traveling along this wire. Calculate the velocity of a transverse wave traveling along this wire.
KPECTED HAS OCCU... Subject ystem S- rchpool.sona- ems.com man Subject Pool tem Department... 6³ 2 [108 W 24,919 Xx :8: F2 3 6. A 150 kg uniform beam is attached to a vertical wall at one end and is supported by a cable at the other end. Calculate the magnitude of the tension in the wire if the angle between the cable and the horizontal is 8 = 46°. X 1832.64 N E 20 F3 $ 4 R HEATRA MAL 2 7 F4 % 5 T F5 ^ 6 tv ♫ MacBook Air F6 Y & 7 44 F7 U M M | L T E 10 * 8 0 30.0⁰ DII F8 ( 9 Beam A DD F9 O O W F10 zoom B P C F11 ISUIH by mi 04 M vauies or roc puffer d + = F12 delete
2. A 3.0-m-long ladder leans against a wall at an angle of 60° with respect to the floor. What is the minimum value of us, the coefficient of static friction with the ground, that will prevent the ladder from slipping? Assume that friction between the ladder and the wall is negligible. Center of gravity 19 TULO L 60⁰ Weight acts at the center of gravity. Known L-30 m Find Me Contro <= 0 about this point. Static friction prevents slipping.
1. (1) Three forces are applied to a tree sapling, as shown in Fig. 12-45, to stabilize it. If FA = 385 N and FB = 475 N, find Fe in magnitude and direction. FB FIGURE 12-45 FC Problem 1. FIGURE 12-46 Problem 2. 2. (1) Approximately what magnitude force, FM, must the extensor muscle in the upper arm exert on the lower arm to hold a 7.3-kg shot put (Fig. 12-46)? Assume the lower arm has a mass of 2.3 kg and its CG is 12.0 cm from the elbow-joint pivot. 2.5 cm FM -30.0 cm- 105° Elbow joint FA
a meter log is a uniform bar of mass m = 77 kg. You want to support it at a rest parallel to the ground. so you place it on a triangle support at 33 cm mark and tie it with a rope on the ground at the 28 cm mark. A) draw your own configuration out. calculate the tension of the rope ____ N, downward, upward, right, left, or none and support force provided by the triangle support _______ N, downward, upward, right, left, or none b) suppose a gumdrop (point mass mb = 14.00 kg) hangs on to the meter log at the 91 cm mark How large will the tension be on the rope? ______ N conceptually explain why it should increase, decrease, or stay the same, compared to part A. C) Now with everything including the gumdrop, the triangle support has been moved away from the rope, to the end of the meter log.Explain why the system itself cannot stay balanced anymore, and the rope goes (T→0). Calculate: rotational inertia of the system below. I = _______ kg·m2Calculate the sizes (+ only) of both the…
a meter log is a uniform bar of mass m = 77 kg. You want to support it at a rest parallel to the ground. so you place it on a triangle support at 33 cm mark and tie it with a rope on the ground at the 28 cm mark. A) draw your own configuration out. calculate the tension of the rope ____ N, downward, upward, right, left, or none and support force provided by the triangle support _______ N, downward, upward, right, left, or none b) suppose a gumdrop (point mass mb = 14.00 kg) hangs on to the meter log at the 91 cm mark How large will the tension be on the rope? ______ N conceptually explain why it should increase, decrease, or stay the same, compared to part A. C) Now with everything including the gumdrop, the triangle support has been moved away from the rope, to the end of the meter log.Explain why the system itself cannot stay balanced anymore, and the rope goes (T→0). Calculate: rotational inertia of the system below. I = _______ kg·m2Calculate the sizes (+ only) of both the…