1. A constant load (= 150 MW) supplied by a hydro and a steam unit. Find the generation schedule for 5 days (120 hours). Assume that generation of hydro unit limited to 12000 MWh. MW Hydro unit: 2 MW Steam unit: F(P₂) = 160+4P₁ +0.025 P²² 20th SP < 100m O < PH <200

1. A constant load (= 150 MW) supplied by a hydro and a steam unit. Find the generation schedule for 5 days (120 hours). Assume that generation of hydro unit limited to 12000 MWh. MW Hydro unit: 2 MW Steam unit: F(P₂) = 160+4P₁ +0.025 P²² 20th SP < 100m O < PH <200

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A d.c. serier generator, having an external characteristic which is a straight line through zero to 50 V 200 A is connected as a booster between a station bus bar and a feeder of 0.3 ohm resistane. Calculate the voltage difference between the station bus-bar and the far end of the feeder qa current of (i) 200 A and (ii) 50 A.
a) Write down the expression of instantaneous voltage for an AC voltage having a Peak value of 220 Volts and a frequency of 50 Hz provided at time t=0, the instantaneous voltage is 220 Volts. What is the instantaneous voltage of the source at time “t = 5 seconds” What is its RMS voltage? b) Two 200Ω resistances are connected in series with one 0.5 H Inductance and two 100μF Capacitance with the power supply of part (a). (i)Draw the circuit diagram of the above network (ii)What is the total impedance of the circuit (iii)What is the max current that flows through the Inductance? (iv)What is the max current that flows through each of the Capacitance? (v)What is the power dissipated in the circuit (vi)What is the power factor of the circuit (vii)What is the resonance frequency of the circuit? (viii) What is the maximum power dissipated by the circuit when it is in resonance
Q1. In which of the following cases, the Electrostatic Discharge (ESD) is more? Explain how the ESD event taken place in both the cases. a. A person walking across a synthetic carpet on a dry day and generates a potential of 15 kV on his body. b. A person walking across a plain ground surface on a dry day and generates a potential of 100 V on his body.
I need the answer as soon as possible
When one coil of a magnetically coupled pair has a current of 5 A, the resulting fluxes p11 and p12 are 0.40 mWb and 0.80 mWb, respectively. If the number of turns N1 and N2 are 500 and 1500, respectively, what is the self-inductance L2? a. 560 mH b. 1080 mH c. 540 mH d. 1060 mH
14: Which of the following circuit elements will oppose the change in circuit current? A)Capacitance, B) Inductance, C) Resistance, D) All of the above. 15: If the current in one coil is steady, what happens to the mutual inductance? C) Doubles, D) Halves. 16. If the flux linkage in coil l is 3Wb and it has S00 turns and the current in coil 2 is 2A. A) Zero, B) Infinity. calculate the mutual inductance. A) 750H, B) SOOH, C) 450H, D) 900H. 17: As Faraday's laws of electromagnetic induction, an em.f. is induced in a conductor whenever it. (A) Lies perpendicular to the magnetic flux, (B) Lies in a magnetic field. (C) Cuts magnetic flux, 18: Calculate the emf when the flux is given by 3sin t + Scos t A) 3cos t - Ssin t. B) -3cos t + 5sint. C)-3sin t - Scos t, D) 3cos t + Ssin t. D) Moves parallei to the direction of the magnetic field.
A high-voltage direct-current generating station delivers 5 MW of power at 178 kV to a city, as depicted in Figure below. The city is represented by resistance R₁ and each of the two wires of the transmission line between the generating station and the city is represented by resistance RTL. The distance between the two locations is 1752 km and the transmission lines are made of 7 cm diameter copper wire. Determine how much power is consumed by the transmission line. Please enter your answer 2 decimal places and in terms of Watt. (for copper-1.72 x 10-8) Vo Station RTL RTL ww RL (city)
H.W:- calculate the potential difference from (0,0,10) to (0,0,6) for both cases. Hint: calculate V,at (0,0,6)then find the difference for the tw solution. Activate Winde Go to Settinos to a
In the figure below, all impedances are in ohms, all voltages are in volts and currents in Amperes. Both sources operate at 60 Hz. X, = 200 n X, = 600 n 80 sin (wt + T/2) x, = 600 2 0.2 ain wt Determine the time dependent current i (A) due to the current Choose... source Determine the time dependent current (A) flowing through the inductance with a Choose... reactance of 200 Ohms due to the current source Determine the time dependent current i (A) due to the voltage Choose... source Choose... Determine the total effective current (A) flowing through the Choose... inductance with a reactance of 200 Ohms
Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average and RMS for both currents. a = 50° T1 50 2 ot Vs = 300 sin 100rt T2 ot
a. For the circuit shown in figure 2, determine the load impedance for maximum power transfer to the load. Assume 50 22 output resistance of the function generator. b. Calculate the maximum average power transferred to the load. c. If the load is purely resistive element, what will the resistance of the load be for maximum power transfer? Function Generator Vs 2.5 KHz 5 V rms 0V DC offset Figure 2 RG! 5 mH High-Q inductor Ground Load
1. Passive voltage response to injected current step is not instantaneous, why not? Key words: time constant, resistance/capacitance properties