1. A boiler feed pump receives 45 li/s of water at 190°C and enthalpy of 839.33 kJ/kg. It operates against a head of 952 m with the efficiency of 70%. Estimate the water leaving temperature assuming that the temperature assuming that the temperature rise is due to the inefficiency of the input energy.

1. A boiler feed pump receives 45 li/s of water at 190°C and enthalpy of 839.33 kJ/kg. It operates against a head of 952 m with the efficiency of 70%. Estimate the water leaving temperature assuming that the temperature assuming that the temperature rise is due to the inefficiency of the input energy.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q.2: A refrigeration system using refrigerant 22 is to have a refrigerating capacity of 80 kW. The cycle is a standard vapor-compression cycle in which the evaporating temperature 42°C. -8°C and the condensing temperature (a) Determine the volume flow of refrigerant measured in cubic is meters inlet at the to the compressor. second per (b) Calculate the power required by the compressor. (c) At the entrance to the evaporator what is the fraction of vapor in the mixture.
The evaporator of a refrigeration system is to be maintained at-12°C.If degree superheat is 7℃, find the temperature of refrigerant entering the compressor.
A heat pump shown is driven by 2.5 MW motor and receives heat from a source at 80 C and deliver energy to a boiler that operates at constant pressure and saturation temperature of 130 C. The water enters the boiler as saturated liquid and leaves as saturated vapor at the same temperature. The heat pump operates with a COP (coefficient of performance) that is 70% of a Carnot heat pump COP. Find: 1- the maximum mass flow rate of water the system can deliver 2- the heat received from the cold source Q, boiler mwater eb TH V HP 2.5 MW TL=80°C
A water pump is used in a heating system to deliver hot water at 91 GPM and 121 ft w.c. The pump efficiency is 90%. What is the water horsepower?
1.In a steam power plant, steam enters the turbine at a pressure of 7.2 Mpa and 550°C and exhaust at 20 Kpa. The turbine inlet is 3 m higher than the turbine exit. Inlet velocity of steam 20 m's, and outlet velocity of 100m/s. a) Calculate the required steam flow for a 2MW plant capacity b.) with 90% stage efficiency, find the quality and enthalpy of exhaust steam
A refrigerator cycle uses refrigerant R-134a and operates between a low-side pressure of 1.5 Bar and high side of 10 Bar. The power input to the compressor 1.88 Kw. find the refrigerant mass flow rate, condensing heat load, and COP of this machine
A refrigeration system has a heat rejected of 430 kw.If COP is 7,find the mass chilled water in the evaporator for a temperature decrease of 16°℃.
A heat pump operates between 36 degrees fahrenheit and 120 degrees fahrenheit . If heat added from the low temp. region is 500 BTU/min. Find the horsepower needed for the compressor power.
Q.7 The COP of the heat pump is found to be 5.62, and the heat pump operates with the source at 25°C, while the heat absorbed is 2.12 kW. What is the amount of heat rejected ?
A steam line carries 200t/h of steam at 40bar connected to a control volume of a spray type desuperheater which is supplied with another line of water at 50 C. Calculate the amount of water that must be sprayed per second to maintain steam at 400 C (at outlet line) when the boiler load causes the first line of steam to leave at 450 C.
An air conditioner using refrigerant 134a as work fluid It is used to keep the temperature of a room at 23 ° C by giving heat to the environment. The house from the walls and heat gain from windows is 250 kJ / min ; 900 W of heat from computer, TV and lamps to the room spreads. The refrigerant is 100 L / min in the form of saturated vapor at 400 kPa pressure to the compressor entering with flow and it left from the compressor 1200 kPa pressure and 70 ° C. a) real COP value b) max COP value c) Calculate the min volumetric flow rate for the refrigerant can have for the same compressor inlet and outlet conditions
iii) the exit area of the nozzle. Take Cp = 1.005 kJ/kg-K and R=287 J/kg-K Q.B3. A heat engine operates between two reservoirs at 400°C and 30°C. Half the power produced by the heat engine is used to drive a Carnot heat pump that removes heat from the cold surroundings at 2°C and transfers it to a house maintained at 27°C. The heat engine is absorbing heat at a rate of 5 kJ/s. i) Draw the complete schematic of the device ii) Determine the thermal efficiency of the heat engine iii) Determine the coefficient of performance of the heat pump iv) Determine the rate of heat loss from the house. v) Determine the minimum rate of heat extraction by the heat pump, and vi) the total rate of heat rejection.