Please answer in typing format 1. A 200/250 V auto-transformerdraws power from a 200 V lineand supplies a 5-kW load witha power factor of 0.5 lagging.A second load of 2 kW issupplied at unity power factorfrom 100 V winding.Neglecting losses, calculatethe current drawn by thetransformer from the 200 Vline and its power factor.[42.64 A, 0.898]

Step 1:Here's how to solve the problem:Find the total apparent power delivered by the transformer.…

Answered: 1. A 200/250 V auto-transformer draws…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Similar questions

For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
The test results of a 5 kVA, 400/200 V, 50 Hz, single phase transformer are as follows. O.C. Test: 400 V, 1 A, 50 W, H.V. side S.C. Test: 12 V, 12.5 A, 60 W, H.V. side Find the full load efficiency and regulation when the power factor is 0.8 lagging.
A 25 kVA, 2 kV(rms)/100 V(rms) single phase transformer is connected between a 120 V(rms) utility supply and a resistive load. The load current was measured to be 20 A(rms). i. Determine the active power of the load. ii. Determine the primary RMS current. iii. Determine the equivalent resistance of the transformer as seen by the utility supply.
Question 9: A single-phase, 240V/1920V ideal transformer is supplied from a 240V source through a cable of resistance 5 ohm. If the load across the secondary winding is 1.60 kohm. Find the primary current flowing and find the power dissipated in the load resistance.
Single phase 10 kVA, 480 V / 120 V to feed a 120 V load from a 600 V source conventional transformer will be used. a. Draw the transformer connection that can do this job. b. In the connection you have drawn, the apparent power of the transformer (in rated operation state, the load power to be transferred) what happened. c. Calculate the maximum primary and secondary winding currents for the connection situation you have drawn.
Chapman Problem 3-4. A single-phase power system is shown in the figure below. The power source feeds a 100-kVA, 14/2.4-kV transformer through a feeder impedance of 38.2 + j140 N. The transformer's equivalent series impedance referred to its low-voltage is 0.12 + j0.5 N. The load on the transformer is 90 kW at 0.85 PF lagging and 2300V. а. What is the voltage at the power source of the system? b. What is the voltage regulation of the transformer? How efficient is the overall power system? С.
i can't figure out the configuration of this xfmr.
1. A 2.4-KVA, 2400/240-V, 50-Hz, the step-down transformer has the following parameters: : RH = 1.59, :XH = 2.50, R₂ = 0.020, X₁ = 0.030, : Rc = 6k2, and: Xm = 8kQ. It is operating at 50% of its load at 0.5 power factor leading. Using the exact equivalent circuit embodying the ideal transformer, determine the efficiency of the transformer. Also, sketch its phasor diagram.
The circuit diagram of a wye wye transformer is shown below. It has a neutral to ground resistor in the right side winding. Again, the transformer turns ratio is 1 in this problem. Calculate the currents IA, IB and IC for the zero sequence currents Ia=Ib=Ic=1/0o Calculate the current in neutral resistor Rn, and the voltage across this resistor. Calculate the neutral to ground current in the right side winding. What is the value of the neutral to ground current in the right side winding when Rn is replaced by an open circuit? Draw the zero sequence circuit of this transformer, and show the zero sequence current flow in this diagram when Rn is finite.
Machine 1
what is the answer for peak to peak ripple and dc output voltage? please answer in 4 decimal places thank you

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning