1. 60 mm 60 mm

Q: F2 = 40 N %3D 4 m F= 70 N %3D 2 m 3 m B. 3m 2 m 3 m

A:

Q: For each of the following systems, give two examples of how a mechanical engineer would be involved…

A: a) Jet for a commercial airliner Mechanical engineer do have a very wide scope for working in such…

Q: X 300 mm D 800 mm B

A:

Q: Water flows with a discharge of 0,02 through a pipe reducer as is shown in the Figure 1. The static…

A:

Q: 4.18 What is the composition, in atom percent, of an alloy that contains 44.5 lbm of Ag, 83.7 lb,m…

A: Given data:         mass of Ag= MAG= 44.5 lbm         mass of Au= MAU = 83.7 lbm         mass of Cu…

Q: The hollow cylinder shown in Fig. P.14.22 is built-in at one end and carries a vertical load of 2 kN…

A: The bending moment due to force is - M=2×1 kNm=2000×1000 NmThe twisting moment due to force is -…

Q: 3 just wearing his suit so you know he's an astronaut, is holding a space space chest along with the…

A: M = 761 g  h = 0.6m          a     distance between E to B         d = 0.7 2+0.62        d =0.92 m

Q: A cylindrical bar with diameter D mm and initial length L mm is tested in uniaxial direction to…

A: Given D = 21mm L = 66mm The formula s = P/a Where, s is the tensile strength, P is the force…

Q: . Figure Q1(b) shows a steel structure with E = 210 GPa and v= 0.3 under combined loading. The…

A:

Q: X 300 mm D 800 mm B

A: For constant angular velocity, angular acceleration is zero,

Q: The pedal and brake drum are illustrated in Figure Q2(b). The 160 mm radius brake drum is attached…

A:

Q: 0.4 m 0.4 m 45 Va

A:

Q: 15 kN 20 kN 2 m m

A:

Q: 3. The shaft AB is made from L2 tool steel (shear modulus 75 GPa), has al diameter of 40 mm, and is…

A: Given data  Shear modulus= 75 GPa  Diameter= 40mm Find the maximum shear stress in AB and BC

Q: 28 cm a? 100 cm 30° V 15 cm

A:

Q: A force F of magnitude F = 90 N is applied at point A. (Figure 3) Determine the magnitude of the…

A: The magnitude of the force F is 90 N

Q: The large window in the figure is opened using a hydraulic cylinder AB. If the cylinder extends at a…

A:

Q: A cylindrical tapered section of diameters 25 mm and 50 mm with a length of 200 mm is pulled along…

A: The Total elongation of the rod cylindrical tapered section. As from the figure i had taken small…

Q: 620 mm 125 350 mm

A: Consider the line diagram of the following figure as shown below – From the line diagram, it is…

Q: 250cm+10m

A: Given Data : 250cm+10m

Q: The assembly consists of a 3-kg vertical pulley A and a 14 horizontal pulley B. If a 2-kg block is…

A: Given data: m=3 kgM=14 kgr=30 mmR=100 mmh=0.1 m Need to determine the speed of pulley B.

Q: A force F of magnitude F = 91 N is applied at point A. (Figure 2)What is the magnitude of the moment…

A: Moment due to a force is the product of force and the perpendicular distance between line of action…

Q: Q1: Find the angle of the force? 250 Ib 110 Ib 25 140 Ibk 40° 90 Ib 170 Ib

A:

Q: The design specifications for the steel shaft AB require that the shaft acquire a strain energy of…

A:

Q: Q2 A small marble at point A of mass 0.5 kg as shown in Figure Q2 is release downward with an…

A: Given data: VA = 2 m/smass of body = 0.5 kgtan θ = 34 θ = tan-1(34) = 36.87°

Q: Express the quantity 254,998m in mm.

A: To convert meter quantity into millimeter one must be familiar with the no. of mm exist in one…

Q: 1.25 m y 180 N '0.5 m F2 0.75 m

A: In the scalar method, the moment can be calculated as follows: In the cross-product approach, the…

Q: A single stage reciprocating compressor takes 1m³ of air per minute and 1.013 bar and 15°C and…

A: Given that, Pressure at the entry of compressor, P1=1.013 bar,Pressure at the exit of compressor,…

Q: Determine Ixx and lyy for the composite section shown below. 50 mm 25 mm 30 mm 25 mm 50 mm 50 mm

A: Given figure

Q: Express the quantity 254,998m in cm.

A: Given: The quantity is Q=254998 m. The unit conversion factor to convert Meter into Centimeter is, 1…

Q: A plate and angle girder is fabricated by riveting the short legs of four (4) angles to a web plate…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: P1.1 For each of the following systems, give two examples of how a mechanical engineer would be…

A: (b) An escalator is defined as the set of stairs which power-driven and used to lift the passengers…

Q: 4. Mm

A: The moment of inertia of the rectangular section can be determined as,

Q: 1. A reservoir contains 2.83 cubic meters of CO at 6895 kPa and 23.6 deg. Celsius. A cylindrical…

A: To find: The diameter of tank  Given data : The volume of CO in tank (Vco)=2.83 m3 The initial…

Q: 2) USE THE METHOD OF SECTIONS TO FIND THE MAGNITUDE AND DIRECTION OF THE FORCE IN BAR CD SHOWN BELOW…

A:

Q: Locate the centroid y of the beam's cross-sectional area. 4 in. 0.5 in. 3 in. -12 0.5 in.

A: Given data:- L section of size=4 in×3 in×0.5 in To find:- Centroid x- Centroid y-

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.