i need the answer quickly 1- When we design a measurement device, the device loading effect on the system to be measuredmust be:a- very lowb- moderatec- highd- very high2- The limiting error of an instrument is :a- Increased as the reading is near the full scale.b- Decreased as the reading is near the full scale.c- Constant for all readings in the same range.d- None of the above.3- The average deviation (D) of a reading of instrument is:a- Directly proportional to the precision of the instrument.b- Inversely proportional to the precision of the instrument.c- No relation between them.

As per bartleby guideline fore more than one question asked only first is to be answered please…

Answered: 1- When we design a measurement device,…

1- When we design a measurement device, the device loading effect on the system to be measured must be: b- moderate a- very low c-high d- very high

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is airside in an airport? and What are the components of the airside? * Your answer
Moving to another question will save this response. Quèstion 9 An OR gate can be replaced by two AND gates and one NOT gate connected adequately. True False Moving to another question will save this response. P Type here to search 近

Please answer with detail and how it is done. Photo is attached with the questions.
1.a. A fiber optic cable has a minimum bend radius of 8 cm and will be mounted in an expansion loop with support messengers. How far should neighboring support messengers be placed when installing this cable?A. At least 16 cmB. Less than 16 cmC. At least 20 cmD. Exactly 20 cm 1.b. A corner pull box has conduits that are separated by 36 cm. If you install a cable in this pull box, what should the minimum bend radius be?A. At least 8 cmB. Less than 12 cmC. Less than 8 cmD. At least 12 cm
Please answer this diligently. Other answers in the internet seems wrong. Please help me understand and solve this problem. I'll give a like. Thanks! Ig2sc = __________; Isc = __________; MVAsc = __________
Suppose the current in this circuit is I = -35 A. The voltage drop across each circuit element is as given in the table below. From this information, determine, for each of these circuit elements, (i) whether an active or passive sign convention is being used for that element, (ii) whether that element is absorbing or producing a net (positive) amount of electrical power. In each answer box within the table below, type the correct choice from among the bold-faced words above. - A A B C A + с B + V₂ Circuit element Voltage drop Sign convention? Absorbing or producing net electrical power? -5 V -6 V 1 V -
How do I calculate that step by step?
A cylindrical 00 AWG copper wire is coated with NEMA class B insulation. The normaloperating temperature of the wire is . What is the maximum current the wire can carry for 1second without exceeding the NEMA temperature rating?
Vdc0 U=12 V Circuit #1 Ried V LED www Ried_series 0.05 Vdc0 U = 12 V 0,04 Circuit 0.03 0.02 0.01 RED LED GREEN LE Set current to 10 mA LED voltages Given the circuit #1 presented above, answer the following questions: BLUE_LEC Red 0.5 1) Determine the value of the V₁ (voltage forward of the LED) for the LEDS RED, VDRED GREEN, VREEN and BLUE, VOBLUES when the current through the LEDs is 10mA, 2) Is the LED in Circuit #1, connected in the way that will be lighting up or not - Justify your answer Green 3) Calculate the value of the resistance Rled in Circuit #1, to ensure that a RED LED will have a current of 10 mA 1.5 2 25 Voltage across LED (V) 4) Calculate the value of the resistance Rled in Circuit #1, to ensure that a GREEN LED will have a current of 10 mA Blue 5) Calculate the value of the resistance Rled in Circuit #1, to ensure that a Blue LED will have a current of 10 mA 6) Given three LEDs, connected in series as shown in the Circui # 2 (below), calculate the value of the…
Please answer in typing format solution please only Please answer all subparts is compulsory to answer in your Please I will like it please
I need the answer as soon as possible
The is the distance from-1 the centre of one slot to the centre of .the next slot a) coil span O b) pole pitch O c) slot pitch O