1-There is a spring with the initial length of 0.4 m and its constant is 200 N/m. The slider attached to this spring which is at position A. The mass of the slider is 3 kg and it is released from the rest at A. If the system is on the vertical plane and there is no friction: A) Find the reaction force from the rod on the slider at position C B) What is tangential acceleration of the slider at position C? C) Determine the velocity of the slider at position B.

Q: Q2. A spring with negligible mass and constant k is attached to one end to a block of mass m and…

A: We will try to approach this problem in work energy method

Q: 3.1.2. [Level 1] Block B has a weight of WB = 18 kg, and the rope at A is pulled down with a force…

A:

Q: . What is the energy stored in the spring if the spring iscompressed 0.5 m?

A: Given data mass = 40 kgspring constant = 3000 N/mCompressed length = 0.5 mWe have to find the energy…

Q: vibrations - show solution

A:

Q: SOLVE STEP BY STEP DONT USE AI

A: Step 1. • Mass of particle = 32.2 lb (which is equivalent to a weight of 32.2 lbf)• Mass of the…

Q: 2) In figure, two blocks are connected by a massless string over a pulley of radius, 2R, and…

A:

Q: The piston of an internal-combustion engine is connected to its connecting rod with a “wrist pin.”…

A: Given   Mass, m = 0.5 kg Acceleration, a = 2500 m/s2 Find   Force on the wrist pin, F

Q: Two springs and two masses are attached in a straight line on a horizontal frictionless surface as…

A: To determine the equation of motion of two mass systems     given

Q: Develop the equation of motion in terms of the variable x for the system shown Draw free body…

A:

Q: RA AC ww RB=? B D RD rrrr

A: from the given dataRA = 106 mmRD = 205 mmRB = ?VD = 8 m/sNA = 2700 rpm

Q: A spring is stretched 3 cm by a force of 6 N. Thus, according to Hooke's Law, the spring DO = 200 N.…

A: From the conservation of energy, the initial kinetic energy of the mass is equal to the final…

Q: 3kg ball connected to horizontal  AB with cable. AB rotates with constant angular velocity w about…

A:

Q: (Figure 1)Block 1, of mass mı, is conn (massless and frictionless) pulley to block 2, of mass m2, as…

A:

Q: The crane shown in the figure is lifting a 186-kg crate upward with an acceleration of 4.21 m/s².…

A:

Q: The collar of mass m = 77 kg in Figure Q14 slides outwards with an initial radial velocity vo = 0.58…

A: Given:  The mass of the collar: →m=77 Kg Initial radial velocity of the collar: →vo=0.58 m/s…

Q: You have your bicycle upside down while you adjust the chain. The chain is wound around the rear…

A: First, draw the diagram of the system: There are 2 revolutions in 1 second, therefore N=2 RPS Now…

Q: The crate, having a weight of 75 lb, is hoisted by the pulley system and motor M. If the crate…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.