1) The sketch below shows the shear diagram for a simply supported beam. Sketch the beam showing the loading. Sketch the moment diagram. The total width of the beam is 5 meters. V [kN] 3 -S 3.4 -66+ -1.5m 3.4 -6.0 -1.5m ImIm

Q: QUESTION 4 There are 47 dowels - 10M, each measuring 910 mm, in a continuous concrete footing. What…

A: Given:Q 4: 47 dowels measuring 10 M10 M=0.785 kg/mlength of dowel=910 mm or 0.910 mQ 5: Length of a…

Q: B -0.2L- L Input units: kNm

A: Given:f=63 KN/mL=8.9 mx=7.29 m

Q: b) A simply supported beam has a rectangular cross-section with a second moment of area (I) of 11.50…

A: Step 1: bending equation  Step 2: Step 3: Step 4:

Q: Determine the shear force V (in kN) and bending moment M (in kN • m) just right of the 4.5 kN load…

A:

Q: Steps: 1. FBD of entire 2. Solve [Fx,[FY, EM for reactions 3. FBD of cut B 4. Solve [Fx,[Fy, EM for…

A:

Q: 2.5 kN/m 75 kN-m A 4 m 1m What are the calculations to create shear force and bending moment…

A:

Q: 2. For the force diagram shown in the accompanying illustration, draw the shear force and moment…

A: To make shear force diagram and bending moment diagram, find support reactionEquilibrium equation…

Q: For the above diagram, given that F1 = 450 N, θ = 30 degrees and d = 5 m, calculate the following…

A: See image below for the explanation

Q: Question contains a hinge in the middle. Find the shear force and the bending moment at the Figure 3…

A:

Q: Write shear & moment equations as function of x and draw shear & moment diagrams for the beam given…

A:

Q: A 77 1/2-4 + D ·(a) This beam will not have an internal bending moment question to the correct…

A:

Q: 1) F1 kN 0.4 m 1.2 m F2 KN 1.2m F3 KN 0.5m The beam is made from mild steel (elastic modulus 200Gpa)…

A:

Q: 1. The axel loads for the truck shown below are P1 = 8 kips, P2 = 6 kips, P3 = 4 kips. Calculate the…

A: Let consider the point C,D,E are the the point where load P1, P2 ,& P3 acting respectively. P1=8…

Q: 2 kN/m 5m B 3 m. 8 kN-m

A: Develop an expression for the shear force V(x) as a function of position (x) along the beam.

Q: A uniform beam is fixed at end x=0 and simply supported at x = L. Find the shape of the center line…

A: Solution: Given Data:   To Find: Shape of the center line of the beam.

Q: Pravinbhai

A: Step 1:Step 2:Step 3:Step 4:

Q: Consider the cantilevered beam shown in the figure below. (Eigure 1) 300 lb 200 lb/ft 6 ft Express…

A:

Q: Analyze the simply supported beam shown in figure-6, by drawing its Shear Force and Bending Moment…

A:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.