1- The pressure drop, Ap, along a straight pipe of diameter D has beenexperimentally studied, and it is observed that for laminar flow of agiven fluid and pipe, the pressure drop varies directly with thedistance, {, between pressure taps. Assume that Ap is a function ofD and €, the velocity, V, and the fluid viscosity, u. Use dimensionalanalysis to deduce how the pressure drop varies withpipediameter.A Qulindor with a diametor D doota unrht in g liquidWhon tha

Given, Pressure drop = ∆p Diameter = D Length = l Velocity = V Fluid viscosity = μ

1- The pressure drop, Ap, along a straight pipe of diameter D has been experimentally studied, and it is observed that for laminar flow of a given fluid and pipe, the pressure drop varies directly with the distance, l, between pressure taps. Assume that Ap is a function of D and l, the velocity, V, and the fluid viscosity, u. Use dimensional analysis to deduce how the pressure drop varies with pipe diameter.

1- The pressure drop, Ap, along a straight pipe of diameter D has been experimentally studied, and it is observed that for laminar flow of a given fluid and pipe, the pressure drop varies directly with the distance, l, between pressure taps. Assume that Ap is a function of D and l, the velocity, V, and the fluid viscosity, u. Use dimensional analysis to deduce how the pressure drop varies with pipe diameter.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Liquid in a tank is being drained through a pipe at tank bottom. The time it takes to drain the…

Q: 'he side thrust F, for a sme -all diameter D, the free-s- nd the angular velocity of Jsing the…

Q: 5: The discharge pressure (P) of a gear pump (Fig. 3) is a function of flow rate (Q), gear diameter…

A: Here, pressure is a function of... P=f(Q,D,μ,ω)So, it can be written as,f1(P,Q,D,μ,ω)=0Here, total…

Q: 04: Use dimensional analysis to show that in a problem involving shallow water waves (Figure 1),…

Q: Liquid flows horizontally through a circular tube filled with sand grains that are spherical and of…

Q: find an appropriate dimensionless

Q: An oil of density 930kg/m and viscosity 0.02 Pa s flows through a pipeline with diameter 3 m at a…

A: Solution Use Renolds model ρvdμwater=ρvdμoil

Q: Applying Dimensional Analysis to the human anatomy studies, it was found that the velocity, c, at…

A: It is required to perform dimensional analysis for velocity

Q: An impeller (axial-flow turbine propeller) in an agitated tank has an output torque (T) whose…

A: Given data Output Torque (T) depends on Volumetric Flow rate(Q), density ( ρ ) rotor diameter (D)…

Q: A fighter aircraft is to operate at 200 m/s in air at standard conditions (p= 1.2 kg/m³). A model is…

A: For prototype:ρp=1.2 Kg/m3μp=μmLpLm=DpDm=20a) Parameters:FD, ρ, μ, V, DNo. of…

Q: For this equation to be dimensionally correct, is u the kinematic viscosity or the dynamic viscosity…

Q: 3. The radius R of a mushroom cloud generated by a nuclear bomb grows in time. We expect that R is a…

Q: The flow rate in a rectangular open channel can be measured by placing a plate along the channel as…

A: Given Data: The width of the channel is b. The height of the water is H. According to the given…

Q: Power generated by a propeller operating in the air (P); it depends on the mass density of the air…

Q: A model propeller of diameter D = 0.8 m is tested in a wind tunnel at pressure and temperature…

Q: 19 The Weber number is a dimensionless parameter relating inertial and surface tension forces in a…

A: Write the given formula for the Weber number. We=ρV2dσ Here, We is the Weber number, V is the…

Q: When small aerosol particles or microorganisms move through air or water, the Reynolds number is…

Q: The force, F, acting on a billboard due to wind depends on it length, l, height, h, the modulus of…

A: As it is given in the question that the force (F) depends in l, h, E, and γa. Here are the…

Q: The variables in a Saybolt viscometer are the time (t) required to empty a certain volume of oil of…

A: The dimensional formula for each variable is shown below.

Q: 1.5 The power generated by a pump PE is a function of the volumetric flow rate Q, the height of…

Q: The frictional pressure drop p for a fluid of density p and viscosity p flowing with a velocity V…

A: Dimensional analysis is a method of reducing the number of relevant variables in a physical problem…

Q: Q1: If an air stream flowing at velocity (U) pasta body of length (L) causes a drag force (F) on the…

A: Force is dependent on the body U,L and fluid viscosity μ Now, we write the dimension formulae of…

Q: Q.5 A plate 1 mm distance from a fixed plate, is moving at 500 mm/s by a force induces a shear…

A: Data given- u= 500 mm/s = 0.5 m/s y= 1 mm = 0.001 m Shear stress = 0.3 kgf /m2 = 0.3 × 9.81 N/m2…

Q: c) The drag force Fp on a cylinder of diameter d and length / is to be studied. What functional form…

A: Write the drag force as the function of given variables as follows: Now use Rayleigh’s method to…

Q: 5. The drag force, fd, on a sphere located in a pipe through which a fluid is flowing is to be…

A: The objective of the question is to determine the drag force on a sphere located in a pipe through…

Q: The time t d to drain a liquid from a hole in the bottom of atank is a function of the hole…

A: Given data td=drain timed=hole diameteryo=initial fluid vol.ho=Liquid depthρ=density of…

Q: The work of adhesion (W) is the energy per unit area associated with bringing two immiscible liquids…

A: Given:The equation is .The is work of adhesion in .The is surface tension in .Concept used:The…

Q: Derive two dimensionless parameters for the shear stress at the pipe wall when an incompressible…

Q: Using dimensional analysis, derive a relation to evaluate the headloss, hf, in closed conduits…

A: given; Using dimensional analysis, derive a relation to evaluate the head loss, hf, in closed…

Q: VisCosity, odel tests run in a laboratory using water in a 0.2-ft-diameter pipe yield the Ty vs. Q…

Q: To have a complete understanding of this, determine parameters such as an area of 60mm bore pipe,…

Q: A group of engineers is planning to built a tunnel going through a mountain range for vehicle to…

A: Reynolds number similarity is used to get the velocity.

Q: Dimensional analysis with Buckinham's Pi Theorem is applied to the relationship between frictional…

Q: Problem 5 s): The discharge pressure (P) of a screw pump (Fig. 5) is a function of flow rate (Q),…

A: Variables are flow rate, screw diameter, fluid viscosity and screw angular speed. Repeating…

Q: An underwater device which is 2m long is to be moved at 4 m/sec. If a geometrically similar model 40…

A: By pressure modelling - PprototypePmodel= ρV2prototypeρV2modelPatmPmodel=…

Q: lease solve this problem, Thank you very much! Figure is attached 1. liquids in rotating cylinders…

Question

100%

1- The pressure drop, Ap, along a straight pipe of diameter D has been
experimentally studied, and it is observed that for laminar flow of a
given fluid and pipe, the pressure drop varies directly with the
distance, {, between pressure taps. Assume that Ap is a function of
D and €, the velocity, V, and the fluid viscosity, u. Use dimensional
analysis to deduce how the pressure drop varies with
pipe
diameter.
A Qulindor with a diametor D doota unr
ht in g liquid
Whon tha

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Trending now

This is a popular solution!

Step by step

Solved in 7 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need an answer quickly
please answer quickly
Consider a boundary layer growing along a thin flat plate. The boundary layer thickness & at a downstream distance x is a function of x, the fluid density p, dynamic viscosity, and free stream velocity V. Use Buckingham's theorem with p, x and V as repeating variables, to obtain the relationship between dimensionless parameters Is. Figure 3.2
F₂ Figure 1: Problem 6.
A dimensional analysis is performed on the drag on a boat. When the effects of viscosity can be neglected, the Euler number based on the drag D experienced by the boat is a function of a Froude number. The effects of the dimensions of the boat can be represented by its length I. The drag on a model of the model is measured as 0.35N. If the ratio of / for a full-scale model to the value of/ for the model is 46, calculate the expected drag on the full-scale boat. Your answer should be to the nearest kN. The properties of the water in the model test matches those for the full-scale boat.
Q.2. The force of impeller depends on the volumetric flowrate of fluid (Q) through the pipe of diameter (d) ,fluid density and viscosity , rotation of impeller (N). By using the dimensional analysis (Buckingham's Theorem), find the relation between the above parameters.
I need the answer as soon as possible
Torque T needed to rotate a disk in a liquid depends on the diameter D, the angular velocity w, the fluid density p and viscosity, and the distance from the wall x. Relate torque to the other variables using the MLT system. Justify reasons for the chosen repeating variables.
Consider the same problem in which an axial compressor with a mean diameter of 0.8 m is being designed to run at 3000 rpm. The whirl velocities at the inlet and outlet are 5m/s and 30 m/s, respectively. The air mass flow rate through the compressor is 2 kg/s at a temperature of 27 °C. Assume C, of air equal to 1000 J/kg-K and Cy = 718 J/kg-K. %3D The temperature change is equal to O 3.14 K 5.28 K 7.42 K OOK
7.2 One-dimensional unsteady flow in a thin liquid layer is described by the equation du + u 6. Use a length scale, L, and a velocity scale, Vo, to nondimensionalize this equation. Obtain the dimensionless groups that characterize this flow.
Buckingham Pi. A mechanical stirrer is used to mix chemicals in a large tank. The required shaft power P is a function of liquid density p, viscosity μ, stirrer blade diameter D, and angular speed w of the spinning blades. (a) use repeating variables p, D, u to find a relation between dimensionless power (1) and w (m2); (b,c) a small 1/3 scale model is used in water to predict the actual required power in a viscous liquid with SG =2 and μ = 12μwater. Find (b) the ratio of speeds, wwater/ wactual, necessary for dynamic similarity and then (c) the predicted ratio of powers Pwater/ Pactual. expecting unit : (a) π1 ~ D ; π^2 ~ D^2; (b) wwater/ wactual: 10^0; (c) Pwater/ Pactual 10^-3 SI constant Patm = 10^5 Pa; pwater - 1000 kg/m^3; pair ~ 1.2kg/m^3; µwater ~ 10^-3 N•s/m^2; pair - 2 x 10^-5 N•s/m^2 ; g = 9.8 m/s^2 =
A boundary layer is a thin region (usually along a wall) in which viscous forces are significant and within which the flow is rotational. Consider a boundary layer growing along a thin flat plate. The flow is steady. The boundary layer thickness ? at any downstream distance x is a function of x, free-stream velocity V∞, and fluid properties ? (density) and ? (viscosity). Use the method of repeating variables to generate a dimensionless relationship for ? as a function of the other parameters. Show all your work.