1- Suppose you are operating a steam turbine where the steam leaving the tUPBIHe 1S at 5 bar. This steam contains 95 wt% vapors. If the shaft work produced by the turbine is 1100 kJ/kg and the high pressure, high temperature steam enters the turbine at 100 bar (abs), what is the temperature of the steam entering the turbine? If water at 10°C is supplied to the steam boiler to generate steam, how much heat is required per kilogram of steam produced? You may assume that heat losses from the turbine are negligible.

1- Suppose you are operating a steam turbine where the steam leaving the tUPBIHe 1S at 5 bar. This steam contains 95 wt% vapors. If the shaft work produced by the turbine is 1100 kJ/kg and the high pressure, high temperature steam enters the turbine at 100 bar (abs), what is the temperature of the steam entering the turbine? If water at 10°C is supplied to the steam boiler to generate steam, how much heat is required per kilogram of steam produced? You may assume that heat losses from the turbine are negligible.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At 50 ° C and 900 kPa pressure, 2 kg of superheated steam refrigerant -134a is cooled at constant pressure until half of it condenses. a) This process is done by paying attention to the saturation lines in T-v and P-v diagrams show. b)Calculate the change in volume.
2. What is the sign of the entropy change for the following? a. Solid sugar is added to water to form a solution b. lodine vapor condenses on a cold surface to form crystals
Task 3 Water is initially at 3 MPa and 300 C (state 1) contained within a piston cylinder device. The Water is cooled at constant volume until it reaches a temperature of 200 C (State 2). The water is then compressed to a state where the pressure is 2.5 MPa (State 3). Sketch the T-V diagram to show the three states and determine the properties at all described states in the table below and the quality where appropriate. State Temperature Pressure Specific Internal Enthalpy Quality | Phase volume energy V u 1 2
Plot the process on pv diagram which show the state points relative to the vapor dome. Label the states 1,2,3.. to indicate the sequence of the change in state.
Suppose we have a piece of a candy bar that has an initial mass of 28g. If we ignite the piece of candy bar (literally burn it), and it increases the temperature of 285.23g of water from 18.95°C to 77.43°C, how many calories per gram of energy did the candy bar provide if the final mass of the marshmallow is 4.45? Note: 1.00 cal = 4.184 J. Give your answer in units of cal/g.
The saturated steam R-134a (Case 1) initially at 900 kPa is subjected to the following processes.a) Find the new pressure and, if any, the degree of dryness when the volume is doubled from the initial with an isothermal process (Case 2a).b) Find the new pressure and, if any, the degree of dryness when the volume is reduced to half of the baseline by an isothermal process (Case 2b).
The pressure of the air in a starting vessel is 40 bar and the temperature is 24°C. If a fire in the vicinity causes the temperature to rise to 65 °C. Neglect anyincrease in the volume of the vessel which is 5 liters. determine the following: a. The thermodynamic process the problem representsb. the pressure, temperature, and volume after the processc. change in internal energy, change in enthalpy and change in entropy
2. 10kg of H₂O in a 1.5m³ tank is initially at 200°C heat loss causes a decrease in temperature to 150°C. find: a. Phase 1 and 2 b. Internal Energy at 1 and 2 c. Heat loss if this system is stationary d. Heat loss if the body moving at velocity of 5m/s and assuming the mass of the empty tank negligible. Tonk A contains 2-kg steam a
Answer it quickly ty
can you answer this question
A vessel of water containing 300 kg of water is initially at 270 K. A 100 kg piece of metal,initially at 1300 K, is placed in the water vessel to cool and the vessel is closed. The specificheat of the metal is 0.6 kJ/kg K and 4.2 kJ/kg K for water. Assume the specific heats areconstant and that the vessel is well insulated.a. Find the final equilibrium temperature after cooling. b. Find the amount of entropy generated within the vessel in kJ/K.
Q1) Choose one only A\ A piston cylinder contains 3 Kg of air at 20 C and 300 Kpa. It now heated up in a constant pressure process to 600K. (1) Find the final volume. (2) Plot the process path in P-V diagram (3) Find the work in the process. B\ Give the phase for the following of water states of water and sketch P-v and T-v diagrams showing the location of each state. 1) T=275 °C, P-5MPa, 2) P-500 KPa, T=151.86 °C, 3)P=750 KPa, T= 200-C, 4) T-200°C, P=2.5 MPa