-1 m 1.5 m -1.5 m B A D 3 kN (а)

Q: Apply the force method to determine the reactions at the supports. Assume C is fixed and A is…

A:

Q: 12 KN/m A Solve for the moment.

A:

Q: Solve for the moments over the supports. Use Method B. 125 kN- 4m A B 50 kN/m - 3 m El= constant

A: The given frame is statically indeterminate frame and cannot be analyzed using the equations of…

Q: D H -B E G -30– -22'– -22' 12→|

A: Considering the FBD of the beam shown below:

Q: Problem #2 A 6m Y kN/m C A B The support at A can be assumed to be a roller. Point C is an internal…

A:

Q: solve and e and f

A:

Q: A beam is part of the framing system for the floor of an office building. The floor is subjected to…

A: Service dead load moment= 65 ft-kipsService live load moment= 63 ft-kips

Q: Apply the force method to determine the reactions at the supports. Assume C is fixed and A is…

A: Given A frame Required  Support reactions using force method

Q: Draw the influence line for the moment at C. Use the analytical method in solving. Assume the…

A: Given: Required : Draw influence line for moment at C and also find maximum ordinate? ordinate at…

Q: Determine absolute maximum moment produced in a simply supported girder shown below that supports…

A: Determine the absolute maximum moment produced in simply supported girder.

Q: The hoist supports the 150-kg engine. Determine the force in members DB and FB. Also determine the…

A:

Q: 9-5. Determine the reactions at the supports, then draw the moment diagram. The moment of inertia…

A:

Q: For the beam and loading shown, determine (a) the magnitude and location of the resultant of the…

A:

Q: Determine the reactions and draw the shear and bending moment diagrams for the beams shown using the…

A: SI=5-3=2Hence, two redundants needs to be selected.Taking VB and VC as redundants.

Q: The beam is supported and loaded as shown. Determine the reactions at hinge A and roller B.

A: ###Determination of Reaction  at Hinge A and Roller B####

Q: F a a A 30° 60° AB

A:

Q: 2. The frame show in the figure is supported by a hinge at A and a roller at E. Compute the…

A:

Q: Q1- The beam shown is subjected to two types of distributed loading. Support A is a pin, support Bis…

A: A beam is a load-carrying component of the building used to resist seismic conditions and overcome…

Q: 40 kN 20 kN 20 kN A IAB = 120(10°) mmB IBC = 90(10°) mm1[C -3 m- -3 m-3 m- -4 m -4 m s ai 8 omuazA…

A:

Q: 6. A 6 m beam shown below has a fixed support at A, roller support at E, and an internal hinged at D…

A:

Q: You didn't solve the problem correctly could you resolve it and please clarify your steps the…

A:

Q: please base your answer on the given choices thank you 1.28kN-m 1.58kN-m 1.78kN-m 2.18kN-m

A:

Q: 2. Determine the reactions at supports A and B. 700 Ib/ft 500 Ib/ft 6 ft 9 ft 6 ft 6 ft 8 ft

A: Consider the following free body diagram: Consider member BD as follows:

Q: Determine the magnitude of the reaction at A and B (lb). Determine the magnitude of force P and Q…

A: Since There isn't Any couple working on D & E .So BM for both side would be same :  Firstly we…

Q: F. Draw the shear force and bending moment

A:

Q: Solve for the moments over the supports in the beam loaded as shown. L 을 0.3BL 0.3BL 2 L BL

A:

Q: The connected bar BC is used to increase the lever arm of the crescent wrench as shown. If a…

A: Given Data : Clockwise moment = 120 N-m d = 300 mm Determine the magnitude of force F required to…

Q: 7) For the following beam a. Sketch the influence line for Re, Vc, and Mc using the Muller-Breslau…

A:

Q: Determine the maximum positive moment created at point D in the beam shown below due to the side…

A: ILD FOR BENDING MOMENT AT D: Maximum ordinate of ILD of BM at D =6×46+4=2.4

Q: A continuous beam carries the following loads. 12 kN/m 20 kN A 4m 3m 3m 1. Compute the moment at A…

A:

Q: (a)Determine the resulting moment at point A when the value of F=30lb and G=75lb. (b)Determine the…

A: A loaded beam is given and it has been asked to determine support reactions at A. Please refer step…

Q: Q6) Method of Sections  This bridge is made of two-force members, joined at their ends.  Each…

A:

Q: Problem 2: For the beam shown in Figure A. Find the reaction at support B (RB) B. Find the reaction…

A: Given data that,

Q: The hoist supports a 175 kg engine. determine the magnitude of the force (in Newton) developed in…

A:

Q: Using the principle of virtual work determine the reactions • • draw the bending moment diagram •…

A: To determine:-Support reactions-Bending moment diagram-Vertical deflection at C

Q: Compute the moments at A and B. Assume B is a roller, A is fixed and C is pinned. El is constant.…

A:

Q: The frame shown consists of members AG, BF, and CE. It is supported by smo pin at B and roller at A.…

A:

Q: The compound beam is pin supported at C and supported by a roller at A and B. There is a hinge (pin)…

A: GIVEN:

Q: a negligible mass m block. It is pinne of 20 kg and negli static friction at B-

A:

Q: Determine the reactions at the supports, then draw the moment diagram. The moment of inertia for…

A:

Q: Given: Required: Consider the cantilever beam shown below. PB = 8 kip 5' A PA = 16 kip 15' Compute…

A:

Q: The beam loaded as shown is supported by 200 kN 25 kN/m a roller at A and B at a fixed support at C.…

A:

Q: The hoist supports the 150-kg engine. Determine the force in members DB and FB. Also determine the…

A: Given : Hoist supports a load of = 150 kg Determine the reactions on the floor at A and C ?

Q: What is the Maximum moment in kN-m. Given: W = 20, a = 1, b 7, and P= 60. PkN am W AN m b m Ry

A:

Beams and Frames

A beam is a horizontal structure or a member which is always subjected to transverse shear loads.