1 LTI System The discrete-time Linear Time-Invariant (LTI) system represented in Figure 1 is described by the impulse response h[n] = u[n], where u[n] is the unit-step sequence. [n]- -y[n] h[n] Figure 1. LTI system. The input to the system is given by n+1, n = 0, 1,2,3 7-n, n = 4,5,6 otherwise. 0, Compute the values of the output y[n] for all n. x[n] =

1 LTI System The discrete-time Linear Time-Invariant (LTI) system represented in Figure 1 is described by the impulse response h[n] = u[n], where u[n] is the unit-step sequence. [n]- -y[n] h[n] Figure 1. LTI system. The input to the system is given by n+1, n = 0, 1,2,3 7-n, n = 4,5,6 otherwise. 0, Compute the values of the output y[n] for all n. x[n] =

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Can you solve this problem ? thank you..
Hello, i need helo to resolve the problem in the picture. The asignature is signal ans systems. I would be very grateful, thank you!!
In the electrical network given in the Figure, the output voltage is taken over the coil. R = 1k ohm, C = 1μF and L = 1 mH. a)Since the switch is closed at time t = 0, the input and the relationship between output voltages. Determine the differential equation shows. b)Find the transfer function. c)Unit impulse and unit step function type input voltages versus output voltages calculate and change changes according to time. Draw it to scale.
Nowadays switching power supplies are commonly used because they offer better efficiency and smaller size compared to a linear power supply, because high switching frequency allows for smaller transformers. One place to find a SMPS (switching mode power supply) is a phone charger. Switching power supplies cause high frequency noise on switching transients. The noise on the output is filtered in various ways but savings may be considered on the output filter (extra inductors and capacitors = extra costs), which means the output will have some amount of noise left getting to the device via the USB cable. Estimate the frequency where the phone charger starts to act as an antenna when the USB cable length is 1.9 meters. Submit your answer in MHz without the unit, rounded to one decimal place. Hint: Either "rule of thumb" can be used.
the question is in the photo.
Kindly give clear and correct diagram
Q9 The discrete-time signals x1[n] is shown in the figure. Carefully sketch each of the following signals: a) x1[2n] - u[n-2] b) x1[n]*u[1-n] c) x1[-2n-3] (d) Compute the signal energy 3 2 -1 *x[n] 1 10 1 2 3
A discrete time signal x[n] is given in Figure 1.
c) Determine whether the system below is a causal or non-causal and give a reason for your answer. y[n]=1/3[ x(n+1)+x(n)+x(n-2)]d) With the aid of mathematical formulation differentiate between the continuoustime unit step signal and the continuous-time impulse signal
101] The discrete-time signals in Figure below are plotted as shown to plot the following: i-xa[2n], ii-xa[-n/4], iii- Xb[-5 - n] find z(n)= x₁[-n+1] + x[n+1], and plot the signal z(n). plot 2xb[n]+2. . . find an even and odd parts of the signal in Xa(n). determine the energy for the signals xb(n) [u(n-1)-u(n-5)] and S = 5 -6-5- 11171 2 3 4 -3-2--1₁ -2 n=al 0 (a) 567 *** T!!! 11 -3 (24 (9 -6-5-4-3 xa(n)[u(-n+3)-u(n-4)] 012345 11 Luffi
a) Design a circuit using 741 op amp IC and 555 timer IC, to generate both Pulse Width and Pulse Position modulated signals. Perform the required calculations to obtain the width of the PPM signal as 200μs. Draw the clear circuit diagram and calculate the values of resistors and capacitors used. b) Simulate the circuit designed in part (a) using appropriate simulation tools(Multisim or Tinkercad) and obtain the output. The answer should include details such as aim, brief procedure, screenshot of simulation circuit along with resultant waveforms and calculations of the practical time-period obtained for PPM output. c) Plot graphs with clear labels and scales for message, carrier and output signal (PWM and PPM). Also discuss your inference and reflection on the results obtained. [Note: Plot graphs on a normal graph paper by hand and attach the scanned copy to the assignment]
Q1: For the system shown in figure (1) 0.5 - R(s) C(s) 16 (s + 4) 1.5 Figure (1) (1) obtain the maximum over shoot, settling time for approximately 5% error, rise time and peak time when the input is a step function (2) sketch the output response for step input.