1- If SNR of 8 KHz channel is 25 dB, the channel capacity is:a) 20 kbps - b) 11.3 kbps c) 66.47 kbps2- If the error correction code is capable to correct up to 4 errors, then the hamming distance is:a) 1 b)4 c) 8 @ 93- Channel capacity increases with the increase of:a) signal power and Noise b) signal power and interference c) signal power and bandwidthd) All of the mentionedd) 80 kbps4- The channel capacity of a noise-free channel with m symbols is:a) Log2 m5- Which coding technique can use fixed length coding:aMorse code b) LZ algorithm c) Huffman code d) Shannon-fano code6- which ARQ introduces higher transmission delay between Tx and Rxa) Selective repeat7- In viterbi algorithm, the metric for decision making is :b) mc) m2d) 2mb) Stop and waitc) continuous ARQd) ARQ with pullbacka) Parity checkb) Hamming distance c) prefix code d) none of the above.

According to the Bartleby guidelines we have to do only first part of this question because there…

1- If SNR of 8 KHz channel is 25 dB, the channel capacty is: a) 20 kbps b) 11.3 kbps c) 66.47 kbps d) 80 kbps 2- If the error correction code is capable to correct up to 4 errors, then the hamming distance is: a) 1 b) 4 c) 8 @9 3- Channel capacity increases with the increase of: a) signal power and Noise b) signal power and interference c) signal power and bandwidth d) All of the mentioned 4- The channel capacity of a noise-free channel with m symbols is: a) Log? m 5- Which coding technique can use fixed length coding: OMorse code 6- which ARQ introduces higher transmission delay between Tx and Rx a) Selective repeat 7- In viterbi algorithm, the metric for decision making is : A Parity b) m c) m2 d) 2m b) LZ algorithm c) Huffman code d) Shannon-fano code b) Stop and wait c) continuous ARQ d) ARQ with pullback

1- If SNR of 8 KHz channel is 25 dB, the channel capacty is: a) 20 kbps b) 11.3 kbps c) 66.47 kbps d) 80 kbps 2- If the error correction code is capable to correct up to 4 errors, then the hamming distance is: a) 1 b) 4 c) 8 @9 3- Channel capacity increases with the increase of: a) signal power and Noise b) signal power and interference c) signal power and bandwidth d) All of the mentioned 4- The channel capacity of a noise-free channel with m symbols is: a) Log? m 5- Which coding technique can use fixed length coding: OMorse code 6- which ARQ introduces higher transmission delay between Tx and Rx a) Selective repeat 7- In viterbi algorithm, the metric for decision making is : A Parity b) m c) m2 d) 2m b) LZ algorithm c) Huffman code d) Shannon-fano code b) Stop and wait c) continuous ARQ d) ARQ with pullback

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

what happens to the information in am if the signal is demodulated
be aware that it's a digital electronics question
Problem 4: Design a synchronous counter using J-K FFs that has the following sequence CBA: 001, 011, 100 and 111, and repeat. Follow the CBA notation: A is the least significant bit and must be on the right, and C is the most significant B, and most be on the left. The undesired (unused) states CBA: 000, 010, 101 and 110 must always go to XXX use the following table: PRESENT State NEXT State A B A Jc Kc Jg Kg JA KA X X 1 X X 1 X X 1 1 X X For the Karnaugh maps, follow the following notation: Ā A CB CB CB
Seven voice signals each band limited to (4 KHz) are to be FDMedwith guard band of (1 KHz) , calculate the required bandwidth andthe carrier frequencies if DSB modulation is used
1. Predict the output from the following devices a) 1 0 MUX D 0 1 0 1 c) 0 C = ? LUSS F = ? MAY 0 0 b) 0 0 DECODER ENCODER D A A = ? B=7
What are the similarities and differences between the information signal m (t) obtained as a result of demodulation and the original information signal m (t) on the modulation side? (first one is original signal)
55.
i need the sol. in 30 min
Y 0 X or Q
The pulse modulation is the process of changing a O binary pulse signal to represent the digital data O binary signal to represent the information to be transmitted O binary pulse signal to represent the information to be received O binary pulse signal to perform the data to be transmitted
The term BER refers to Select one: O Bit Error Rate O Binary Error Rate Baud Error rate Bit Efficiency Routing
I need answer within 30 minutes please with my best wishes Ali