1 - For experiment A: a ) Plot on the same graph sheet the torque ( x - axis ) against the speed (y - axis ) for different values of I e b) Calculate the efficiency of the d. c. motor for each step and then plot the set of curves (efficiency ) y - axis against Ia ( x - axis ) on the same graph sheet. 2 - For experiment B: a ) Repeat 1 - a for different values of Re1 b ) Repeat 1 - b. 3 Give your comments about the resul ts obtained in this experiment.

1 - For experiment A: a ) Plot on the same graph sheet the torque ( x - axis ) against the speed (y - axis ) for different values of I e b) Calculate the efficiency of the d. c. motor for each step and then plot the set of curves (efficiency ) y - axis against Ia ( x - axis ) on the same graph sheet. 2 - For experiment B: a ) Repeat 1 - a for different values of Re1 b ) Repeat 1 - b. 3 Give your comments about the resul ts obtained in this experiment.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1.4 A dc shunt generator when driven without connecting field winding shows an open circuit terminal voltage of 12 V. When field winding is connected and excited, the terminal voltage drops to zero because (a) field resistance is higher than critical resistance (b) there is no residual magnetism in the field circuit (c) field winding has got wrongly connected (d) there is a fault in armature circuit
Two de generators each having linear characteristics that operate in parallel. One machine has a terminal voltage of 480V at no load and 220 V at a load current of 100A, while the other machine has a voltage of 470 V at no load and 200 V at 120 A. calculate the current in each generator and the bus bar voltage when the total load is 180 A. What is the kilowatt output of each machine under this condition?
Q3. Write if the shown statements are TRUE or FALSE. 1- In DC machine the induced e.m.f is proportional with flux only. 2- The Ta/l a graph of a d.c. series motor is a straight line throughout. 3- In a DC motor the direction of the shaft rotation can be change by changing the polarity of the power supply. 4-The critical resistance is less than armature resistance in shunt generator. 5-As the load is increased, the speed of a d.c. shunt motor increases slightly.
answer all parts please
4-pole, d.c. shunt motor has a flux per pole of 0.04 Wb and the armature is lap-wound with 720 conductors. The shunt field resistance is 240 Ω and the armature resistance is 0.2 Ω. Brush contact drop is 1V per brush. Determine the speed of the machine when running (a) as a motor taking 60 A and (b) as a generator supplying 120 A. The terminal voltage in each case is 480 V. 5 3 K4 8 Derive the Torque equation of a D.C Motor.
None
A 350 V shunt motor runs at it's normal speed of 720 r/min when the armature current is 90 A. The resistance of the armature is 0.3 ohm. Determine the following: (1) The kΦ1 of the motor. If armature current is 45 A and a resistance of 0.4 ohm is connected in series with the armature and the shunt field remaining constant determine the following: (2) The new kΦ2 of the motor. (3) The new speed of the motor in r/min If the current is 45 A and the shunt field is reduced to 75% of it's normal value by increasing resistance in the field circuit, determine the following: (4) The new kΦ2 of the motor. (5) The new speed of the motor in r/min
Report 1- Sketch speed (y-axis) torque (x-axis) characteristics of compound DC motor for three connections on the same sheet and discuss the graphs. 2- Sketch armature current (y-axis) torque (x-axis) characteristics of compound DC motor for three connections on the same sheet and discuss the graphs 3- Calculate the efficiency of d.c. motor for each connection. 4- Plot the efficiency (y-axis) against Im (x-axis) for each connection. 5- Give your comments about the results obtained in this experiment 6- Mention the applications of each type of motor?