1) Find to in terms of input voltages 2) Find out put impedance of the circuit if of the the op amp is output impedance-

Q: Compare long-channel MOSFETS with Short-Channel MOSFET devices. Give at least three differences.

A:

Q: Immediately after a reset, CS=FFFF and IP=_______. (Give four hex digits.)

A: Ans :-  0000H

Q: Which one is the correct statement? Select one: O a. All of the other statements are incorrect. O b.…

A: The HMI is linked to the SCADA supervisory computer to provide live data to drive the mimic…

Q: Consider a garden house where the radio channel TRT Radyo 4 is constantly open has an installed…

A: The power consumption of the radio is given and the average usage time is

Q: What is matched termination?

A: In this question we discuss what is matched termination.

Q: (a) The varable yesistoe in the CirCuit of Fil below ie adjnsted for Max power transer to Ro. Finod…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: * what ---- their phone number?( are, is, does, have) are is O does O have O

A: It is given that: What -------- their phone number?

Q: A television reciever used for receiving TV signals from a satellite. The specifications of the…

A: Step 1:Step 1: Calculate the System Noise Temperature (Tsys)The system noise temperature (Tsys)…

Q: 5. Convert decoder to H.A.

A:

Q: Explain the function of a repeater in a communication system.

A: A repeater is an electrical device used in a communication system that receives signals and…

Q: pr application for the FM ?*

A:

Q: lo avold corruption during transmission, the code-word snould be Select one: O a. None of the…

A: The code-words should be far apart from one and another as possible  So even when the vectors…

Q: What is meant by CRT ?

A: In this question we need to answer What is meant by CRT .

Q: 2) what is aparallel circuit?what cct. Characteristics indicate that aparallel cct. Condition…

A: Since, you have posted multiple questions. We can answer only one of them. So, i solved Q. 2 for…

Q: Q4/ Why the performance of multimode graded index is better than multimode step index? Q5/ Design…

A: According to guidelines solving only one question at a time4) To discussWhy the performance of…

Q: What are the three most important effects due to multipath in mobile radio channel? Explain each…

A: We have given the problem What are the three most important effects due to multipath in mobile radio…

Q: d. refer to (b), when the frequency of the test tone is changed to 7 kHz and the percentage of…

A: We need to find out the carrier swing for given modulation .

Q: Complete the number conversions indicated. Note that all binary numbers are two’s complement…

A: A binary number is a number which is expressed in base-2 system by using only "0" or "1" digits.…

Q: Which of the statement is refers to call in progress tone? O Itis tone indicated as user call is…

A: progress tone includes the busy signal, ring-back, and dial-tone when we setup a call it include…

Q: What frequencies found in RTK radios require licensure?

A: As per the code of federal regulations, it holds the complete rules of FCC. The federal regulations…

Q: Differentiate MCB and RCD and Explains its purpose in an installation?

A: MCB is an electrical switch designed for automatically working to protect the electrical circuit…

Q: How to identify the miswire in a UTP cable using a cable tester, write the steps in your own words?

A:

Q: IV) What is Cell Relay? Give applications.

A: As per Bartleby guidelines we are allowed to solve only one question,please ask the rest again. The…

Q: don't use third party content 47. Explain the concept of ladder filters.

A: Ladder filters are a type of electronic filter commonly used in signal processing and…

Q: Explain the safest one to use in an aircraft GPS OR DGPS

A: Given: GPS or DGPS

Q: Q. No 3. In a Public Switch Telephone Network (PSTN), how the analog speech signal is converted to…

A: PSTN represents Public Switched phone phone Network or the standard circuit-exchanged phone…

Q: Which is easier to use a bnc connector or sma connector

A: BNC are bigger and easier and faster to handle. SMA are quite a bit higher in frequency capability…

Q: Determine the carrier swing of an FM broadcast transmitter a. when modulated 60 percent b. when an…

A: As per the policy we are supposed to answer only the first 3 questions. Hence plaese post the last…

Q: Que.26 What are Optical couplers? What are the functions of Couplers?

A: Given:Optical couplers.Required:We need to tell about optical couplers and their functions.

Q: Subject is Communication system. In a public switch telephone network (PSTN),how the analog speech…

A: There are majorly three steps for converting analog signal to digital signal. 1. Sampling of the…

Q: 4 Operation of a PMMC instrument is not effected by_____________ A-power B-current C-voltage…

A: PMMC : ( Permanent Magnet Moving Coil ) Principle of Operation : When a current carrying conductor…

Q: 1. Briefly describe the AMPS system. Describe also the three classifications of AMPS cellular…

A: Telephone communication-  Telephone communication is a defined as a communication in which the…

Q: 3- Design a four bit up down (Asynchronous and Synchronous) counter.

A:

Q: rect(f) 47 rectlt) = - 4 4 2 €7 a12 11.14 rectlt) ya -a/2 rect (t) → must have unit area tep Ult) >…

A:

Q: 9. a) When a mobile phone user attempts to make a call ,the cell phone connected to a base station…

A: Part (i):A transceiver is defined as the combination of transmitter and receiver in a single…

Q: 3. Describe the Volts per Hertz Control for three pnase induction motor. 4. Draw the torque speed…

A: 3.Volts per Hertz Control The voltage enforced command is calculated directly from the applied…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.