1- Determine the resistance spreads for 3-bit D/A convertor for binary weighted resistor and for the R-2R ladder types. 2- An amplifier has 20dB gain and 1MHz bandwidth, what is the new gain and bandwidth after a negative feedback is applied with de-sensitivity factor D=5? 3- Determine the required order for a Butterworth LPF to provide 20dB attenuation at w/w,-2.

1- Determine the resistance spreads for 3-bit D/A convertor for binary weighted resistor and for the R-2R ladder types. 2- An amplifier has 20dB gain and 1MHz bandwidth, what is the new gain and bandwidth after a negative feedback is applied with de-sensitivity factor D=5? 3- Determine the required order for a Butterworth LPF to provide 20dB attenuation at w/w,-2.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1. (a) Using the hybrid-pi model with early voltage effect, compute the small signal voltage gain, Av, input resistance and output resistance for the CE BJT amplifier shown below. Vec = 12 V B=100 VELON) = 0.7V V = 100V R = 93.7k2 %3D E R=6 kN Rg=0.5 k2 C, E R2= 6.3 k2 Figure Q1(a)
A transistor amplifier circuit is biased so that the quiescent point is to the far left of the load line midpoint. What do you expect to occur when the input voltage begins to vary? O The output voltage will be distorted on the bottom because it will hit the lower limit for VCE before the input voltage arrives at its peak. The output voltage will be distorted on the top because it will hit the upper limit for VCE before the input voltage arrives at its peak. O The output voTransistor's output voltage will look like the input voltage amplified and inverted. The output voltage will be zero (flat).
Find the desired in point 54 with finding what you can find.
Help
B. Make a sketch of the channel region when VGS=VGS-OFF and make a sketch of the channel region when ID=IDSS and explain why each channel has this shape. C. Assuming that the measured values for the PF5102 were VGS-OFF= -1V and IDSs 10mA, design a common source amplifier for ID=4mA and VDS= 4V using a 12V supply and combination biasing without degeneration as you did in the laboratory. D. Find the input resistance, output resistance, and voltage amplification of your design using the hybrid-pi model and explain how you measured these parameters in the laboratory.
Problem: - Q1. For a MOSFET feedback bias circuit, calculate the values of Ip, Vcs and Vps given of RG= 12M2, Rp = 1.6KQ, and the data sheet gives VGs (TH) = 2.5V, ID(ON) = 5mA, VGs(ON) = 6.5V with VDD =14V.
Şe s deve e R yuk utrerncinin ak reguamekteor. M. deyamua kalacak şekinos ie maksimum dečerini hesapie The current of a load resistance Rp is regulated with the feedback circuit shown in the figure. The Mosfet operates in saturation. What is the maximum value of Rp while M, remains in saturation? Circuit parameters / Bevre Perametreleri VREF=2.8 V, Rs=100 , w/L=54/0.18, VoD = 41 V, H,Cox = 200 µA?, VTH = 0.4 V, A = 0, A, = 00. VDD I. * RD A1 VREF Rs O a. 15.96 k O b. 23.94 k O c. 18.62 kn O d. 13.30 kn O e. 7.31 ko O f. 21.28 kO O g. 9.97 kn O h. 4.65 kn WH.
Derive the output resistance using small signal model for the following circuits, assuming the transistor has output resistance of a transistor is ro and transconductance of gm. Rout PPA Rout Vb- Vbo Rout Rout Vdd Vb- Rout
Problem #5 Use the following process parameters Tox = 9.10 "m, 4, = 350.10 m /V-S1.V= 0.7V,Y = 0.45 For the amplifier shown below, assume A-0 (a) What is the small-signal gain if M, is in saturation with lo 1mA? (b) Compute the value of input voltage and the small signal gain when M, is at the edge of triode region (c) Compute the value of input voltage and small signal gain when M, is pushed further into triode region by 50mV 3V 2kQ VOUT VIN M,(50/0.5)
Question Vvv Full explain this question
Using the small signal equivalent model, find the input and output impedance of such E-MOSFET circuit.
Tag questlon In a class B push-pull amplifier, crossover distortion occurs when both transistors are on and the input signal voltage must exceed VBE before a transistor cutoff . Select one: O True O False