Q3.voltmeter should measure with FSD =150V(rms). The germanium diodes are used in the bridge rectifier.CalculateDesign a full wave rectifier voltmeter with PMMC instrument parameter are given in Q2 . The aca) Multiplier resisterb) Pointer indication for 25 V(rms) and 50 V(rms)c) Sensitivity of the design full wave rectifier voltmeter. The parameter of PMMC instrument are as follows:Rm=1.7k2 and FSD of PMMC is 100µA

In the full-wave rectifier, the germanium diode is used to convert alternating current to a series…

1 Design a full wave rectifier voltmeter with PMMC instrument parameter are given in Q2 . The ac Itmeter should measure with FSD =150V(rms). The germanium diodes are used in the bridge rectifier. lculate a) Multiplier resister b) Pointer indication for 25 V(rms) and 50 V(rms) c) Sensitivity of the design full wave rectifier voltmeter.

1 Design a full wave rectifier voltmeter with PMMC instrument parameter are given in Q2 . The ac Itmeter should measure with FSD =150V(rms). The germanium diodes are used in the bridge rectifier. lculate a) Multiplier resister b) Pointer indication for 25 V(rms) and 50 V(rms) c) Sensitivity of the design full wave rectifier voltmeter.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

b. Calculate the following about the circuit in the figure (If silicon diodes are employed in the rectification);i. the peak value of the output voltage considering the drop across each diode, Vpk.ii. the average voltage, Vdc. iii. The current through the load resistor, IL.iv. The current diode, Id.v. The frequency of the output signal, Fout.vi. Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch a graph of the input and output voltage against time.
Q4/: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10³t)] rms input signal has a load resistor of 3.3k2. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VL-P) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de voltage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.
Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical model, what PIV rating is required for the diode? The transformer is specified to have a 12 Vrms secondary voltage for the standard 110 V across the primary.
04: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10°t)] rms input signal has a loud resistor of 3.3k0. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VLp) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de valtage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.
2. A circuit of 3-Phase Controlled Half Wave Rectifier with Resistive load is as below. A T2 eleeeeee B If the firing angle, a are to set at r/9, complete the circuit operation for the whole cycle (0° to 360°) for the period stated in Table 1. By using appropriate scale, draw a waveform of Average Output Voltage, Vo(avg). Derive an equation for the average output voltage, Vo(avg). If the rectifier is connected to 208V, calculate the Vo(avg) if the load is purely resistive. (C3, CLO1) Duration Period s1 S2 S3 Vout 1 0° – 20° 20° – 50° 3 50° – 120° 4 120° – 140° 140° – 170° 170° – 240° 7 240° – 260° 8 260° – 290° 290° – 360° Table 1
Q.3 Consider the half-wave rectifier eircuit shown in Figure B3. Assuming practical diode model with turn on voltage of 0.7 V. Si 4V 7:1 + 120 Vrms 60HZ V. pri Ves RL V. Figure B3 a) Determine the Vipp) voltage for Vee- b) Draw and label completely the output voltage wavefom. State the peak value and the frequency of the wavefom.
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: Peak AC voltage Vm of the source a) b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance vs(t) K Load UL
Draw the following rectifier circuits with an input voltage of 12 Vrms and an RL=2K. Determine the output voltage and the current in RL. Plot these waveforms indicating the peak values and the time as per calculation. Also solve for the output DC value. Use silicon diode/s in your analysis. Half wave rectifier circuit (include the diode voltage analysis), Full wave bridge rectifier circuit, Full wave rectifier using center tapped transformer
Q1: a) Derive the proof of for the following expression for half wave rectifier. V V avg b) Derive the proof of for the following expression for full wave rectifier. 2Vp V avg
Q2] A three phase half wave controlled rectifier has an input voltage which is 420 Vrms line to line at 50 Hz, and the load is high inductive. If the trigger angle (a = 90"), answer the following: a) Draw the rectifier circuit. b) Draw to scale the input voltage, the load voltage and the current waveforms. c) Determine the mean values of the load voltage.
For the full wave rectifier circuit shown, if vs=15sin(120nt) (V), R=10052, assuming constant voltage drop with VDo=0.7 J. 1. LDraw clearly and accurately with details the following waveforms: Source voltage (vs), load voltage (v.) 2. Describe in details the operation of the circuit indicating which diodes will be ON which ones will be OFF and state clearly the condition at which each diode will be ON or be OFF. 3. Calculate the mean load current (IRmean) given Vmean=2Vp/T. 4. Calculate the PIV. ac line Us voltage D2 Maximum size for new files: 10MB, maximum attachments: 2 Files 79 CE255/EE255 (01)-..