1. A full-wave bridge rectifier isolated from the 220 V rms power line by a transformer. Assuming the diode voltage drops are 0.7 V. i. What turns ratio should the transformer have in order to produce an average current of 1A in a 10 2 load? ii. What is the average current in each diode under the conditions of (i)? iii. What minimum PIV rating should each diode have?

1. A full-wave bridge rectifier isolated from the 220 V rms power line by a transformer. Assuming the diode voltage drops are 0.7 V. i. What turns ratio should the transformer have in order to produce an average current of 1A in a 10 2 load? ii. What is the average current in each diode under the conditions of (i)? iii. What minimum PIV rating should each diode have?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In a full wave bridge rectifier, the transformer secondary voltage is 20sinwt. The forward resistance of each diode is 252 and load resistance is 1.5KN. Calculate, i. Im ii. Idc iii. Pdc iv. Pac V.
b. Calculate the following about the circuit in the figure (If silicon diodes are employed in the rectification);i. the peak value of the output voltage considering the drop across each diode, Vpk.ii. the average voltage, Vdc. iii. The current through the load resistor, IL.iv. The current diode, Id.v. The frequency of the output signal, Fout.vi. Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch a graph of the input and output voltage against time.
Calculate the capacitor value Conditions: 1st That, for the calculation of the peak voltage of the rectifier output, it is 9V. 2nd That the ideal ripple voltage is equal to 10% of the peak voltage at the output of the rectifier. 3rd That the maximum load current is 0.009A
04: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10°t)] rms input signal has a loud resistor of 3.3k0. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VLp) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de valtage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.
Create a rectifier circuit that provides an output of 100vdc by using the following circuit: a. Half Wave Rectifier In each circuit, calculate the following if the power is taken from a 220V line AC supply a. transformer peak voltage rating b. diode PIV ratings c. transformer turns ratio
1. In a single-phase diode bridge rectifier, I-10A(rms), Is1=8A(rms), and DPF=0.9. Calculate Idistortion, %THD, and PF.
For a full wave controlled rectifier with pure resistive load (R=100),the supply voltage is (V-50Sin314t). When the firing angle (a =0%) determine the followings: 1) The mean (dc) value of the load current. 2) The RMS value of the load voltage.
write clean and descriptive
Q.3 Consider the half-wave rectifier eircuit shown in Figure B3. Assuming practical diode model with turn on voltage of 0.7 V. Si 4V 7:1 + 120 Vrms 60HZ V. pri Ves RL V. Figure B3 a) Determine the Vipp) voltage for Vee- b) Draw and label completely the output voltage wavefom. State the peak value and the frequency of the wavefom.
QUESTION 2.. A load is connected in the Full Bridge rectifier circuit (Four Diodes). Usedtransformer primary voltage value is 220 V (rms). The transformer winding ratio is 1:10.Using the 0.7 V model of the diode,Load Rating: 7K OHM d) Find the effective value of the load voltage.e) Find the effective value of the load current.