1 /Choose the correct answer 4- Higher temperature during placing and setting increases the very b) later strength b) early strength c) not effect d) all of them. 5- hydration of cement can take place only in b) dry capillaries b) air capillaries C) water-filled capillaries. 6- Direct tension test It is difficult due to b) The amount of Ca (OH)2 b) secondary stresses 4- Factors affecting the strength of concrete... a) testing parameters b) curing conditions 5- the dry cube will give a) equal b) higher wing d) all of them c) The shape of sample c) proportions of materials strength than the wet cube c) lower d) all of them

1 /Choose the correct answer 4- Higher temperature during placing and setting increases the very b) later strength b) early strength c) not effect d) all of them. 5- hydration of cement can take place only in b) dry capillaries b) air capillaries C) water-filled capillaries. 6- Direct tension test It is difficult due to b) The amount of Ca (OH)2 b) secondary stresses 4- Factors affecting the strength of concrete... a) testing parameters b) curing conditions 5- the dry cube will give a) equal b) higher wing d) all of them c) The shape of sample c) proportions of materials strength than the wet cube c) lower d) all of them

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5 - Why dolomitic aggregate is not preferred in concrete.A) Increases the vacancy rate.B) It creates expansion.C) AllD) Because it is inertE) Increases permeability.
On most rigs cement materials are handled in bulk, which makes blending and mixing much easier. a. True b. False
1.Curing is the -----in which the concrete is protected from loss moisture. 1.process 2. progress 3. durability 2.All formwork should be eased gradually in order to ---- the load being suddenly transferred to concrete. 1.light 2. prevent 3. car fully 3.Width of gravity wall concrete block between----mm 3.40-100 1.30-80 2.40-90 4.The metal Ties in Gravity walls are coated with------ 1.hot tar 2. cheap material 5.EPS made from------ 1.polystyrene 3.hot plastic 2. monomer styrene 3. photolysis 6.Thermal insulation has greatest potential for reducing----- 1.001 2.CO2 3.03 7.Reason of clay Bricks contain-----whit crystals that appear irregular. 1.soluble salt 2. binding coarse 3. light material 8. Gable window are provided in gable end of 1.floor 2. frame 3. roof 9.Failure occurs in long column due------ 1.lateral instability 2. axial load 10.TO decrease the soluble salt inside brick using------ 2. saturation 1.drying 3. soaked 3. material failure
Situation 5: The compound bar, composed of the three segments shown, is initially stress free. Compute the stress in each material if the temperature drops 25°C. Assume that the walls do not yield and use the following data: A (mm²) a (/*C) E (GPa) Bronze segment 2000 19.0 x 10-6 83 Aluminum segrnent 1400 23.0 x 10-6 70 Steel segment 800 11.7 x 10- 200 - 500 mm→- 400 mm- 800 mm Aluminum Steel Bronze 17. Compute the stress in the bronze bar a. 31.6 MPa (T) b. 31.6 MPа (С) 18. Compute the stress in the aluminum bar. а. 45.1 MPа (Т) b. 45.1 MPa (C) 19. Compute the stress in the steel bar. 79.0MPA (T) 79.0MPA (C) 13.6 MPa (T) 13.6 MPa (C) c. d. 54.1 MPа (Т) 54.1 MPa (C) с. d. a. C. 97.0 MPa (T) b. d. 97.0 MPa (C)
PR The high strength of rapid hardening --- cement at early stage, is due to its Finer grinding/Increased silica cement. Finer grinding/Increased lime cement. Coarser grinding/decreased lime cement. Coarser grinding/Increased silica cement. i need clear ans and solve very very fast in 20 min and thank you | DYBALA The specific applications of the rice hush ash cement are Mass concrete Hot weather concreting Cold weather concreting marine constructions
Water/cement ratio of concrete is the ratio of Volume of water to the volume of cement Volume of water to the weight cement Weight of water to the weight of cement Weight of water to the volume of cement (a) (b) (c) (d)
Which of the following is NOT a benefit of using SCMs? Increase required concrete curing time Increase long term strength Reduce permeability Increase the resistance to chloride ions
If a water reducer is added to the concrete mix without changing other ingre-dients, what will happen to the properties of the concrete? If the intention ofadding the water reducer is to increase the compressive strength of hardenedconcrete, how can this be achieved
Q/Choose between parentheses. 1-- The compound of cement which reacts mainly with sulfate salts is ---------------(C3S,C2S,C3A,C4AF) 2-- When a bar is subjected to change of temperature and its longitudinal deformation is prevented, the stress-induced in the bar is due to -----(tensile,compressive,shear,temperature,Clear selection) 3--If the compressive strength of standard solid clay bricks is 14 MPa, the failure force equals to------(226.2 kN,386.4kN,436.5 kN,400.6 kN,450.4 kN) 4-- for quality control of Portland cement , the test essentially done is --------(setting time of cement, compressive strength of cement mortar,Soundness of cement paste,Tensile strength of cement mortar,all the above) 5-Stress-strain curve ------------(is the percentage of stress and strain ,is the relationship between stress and strain,is the deference between stress and strain curve ,None of these,Clear selection) 6-------------- are the type of bricks which can withstand high temperature as a construction…
Which one of the following sentences is not correct? a. For many years, tensile strength has been measured in terms of the compressive strength. b. The modulus of rupture where the normal-weight concrete has an fc of 4000 psi is 474 psi. С. For lightweight concretes tensile strength depends largely on the porous aggregate. d. For normal weight concrete, the tensile strength depends primarily on the strength of bond between hardened cement paste and aggregate. 13:54
The amount of cement (kg) in 1 m3 of mortar with the mix (1:2) is definitely - than that in 1m3 of concrete with a mix (1:2:4). O equal to O more than O less than