(1) Below are the data table for the brayton cycle that was on the test when it is operated as a heat engine. Use this data to determine Q, Qc Wout and the efficiency of the heat engine. Show your work on a separate sheet of paper, but summarize your results in the last row of the table below. Process Q (kJ) Wę (kJ) ΔΕ.» (kJ) 12 562 125 437 23 0 261 -261 3-4 -401 -89 -312 4 → 1 0 -136 136 NET 161 161 0 QH= Qc: WOUT n =

(1) Below are the data table for the brayton cycle that was on the test when it is operated as a heat engine. Use this data to determine Q, Qc Wout and the efficiency of the heat engine. Show your work on a separate sheet of paper, but summarize your results in the last row of the table below. Process Q (kJ) Wę (kJ) ΔΕ.» (kJ) 12 562 125 437 23 0 261 -261 3-4 -401 -89 -312 4 → 1 0 -136 136 NET 161 161 0 QH= Qc: WOUT n =

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Constants A monatomic ideal gas that is initially at a pressure of 1.54x105 Pa and with a volume of 7.50x10-2 Part A m° is compressed adiabatically to a volume of 4.40x10-2 m³ . What is the final pressure? Express your answer in pascals. You may want to review (Page). For related problemsolving tips and strategies, you may want to view a Video Tutor Solution of Adiabatic compression in a diesel engine. ? p = Ра Submit Request Answer Part B How much work is done by the gas during the compression? Express your answer in joules. ? W = J Submit Request Answer
What is the total entropy change if a 0.440 efficiency engine takes 3.78E3 J of heat from a 348 degC reservoir and exhausts it to a 46.3 degC reservoir?
What is the work output per cycle of a Carnot engine that operates between reservoirs at 600 and 300 K if the engine absorbs 100 J per cycle? Please answer this and justify your answer
Assume you are given the following and you have to calculate q (heat), w (work), and delta U using a cycle. 1 mole of an ideal monatomic gas. The initial volume is 5L and the pressure is 2.0 atm. It is heated at a constant pressure until the volume of 10L is achieved.
. A rigid container (0.066 m3) is filled with an ideal gas (Cv = 2.5R) at 501K and 1.1 bar. Calculate the entropy changes asked in below. When an axial mixer is installed in a container and 15,000 J of work is applied to the gas under the insulation process, what is the entropy change of the gas?
In an isentropic process, the entropy is a constant. By using a schematic diagram, indicate the isentropic process(es) in a typical Carnot Cycle. Explain why they are isentropic.
A steam power plant operates on the reheat Rankine cycle. as shown in the schematic diagram (Fig. Q 2). Steam enters the high-pressure turbine at 12.5MPa and 550o C at a rate of 7.7 kg/s and leaves at 2 MPa. Steam is then reheated at constant pressure to 450o C before it expands in the low-pressure turbine. The isentropic efficiencies of the turbine and the pump are 85% and 90%, respectively. Steam leaves the condenser as a saturated liquid. If the moisture content of the steam at the exit of the turbine is not to exceed 5%, then make all the necessary assumptions and determine(a) the condenser pressure,(b) the net power output, and(c) the thermal efficiency.Draw an accurate T-s diagram of the cycle and label all the property values on this diagram. ans also comment on answer
Show that the slope of P-V curve for an adiabatic process is greater than that for an isothermal process.
Topic: Thermodyamics (also included in Chem). Please explain what the Carnot cycle or a heat engine is about step by step.
A refrigerator with a coefficient of performance low-temperature reservoir during each cycle. operate the refrigerator for a cycle? of 1.75 absorbs 3.45 × 104 J of heat from the How much mechanical work is required to
A heat machine uses 1 mole ideal diatomic gas through that cycle shown in Fig. (a) Show that the ab process is isothermal compression. (b) During which process is heat absorbed by the gas? During which process is heat dissipated? How do you know? (c) Find the temperature at points a, b, and c (d) Find it engine thermal efficiency.