1-95. The pin support A and roller support B of the bridge truss are supported on concrete abutments. If the bearing failure stress of the concrete is (īai), – 4 ksi, determine the required minimum dimension of the square bearing plates at C and D to the nearest in. Apply a factor of safety of 2 against failure. 150 kip 100 kip B 200 kip 300 kip 300 kip 300 kip 300 kip F6 ft--6 ft--6 ft-6 ft--6 ft-|-6 ft-| Prob. 1–95

1-95. The pin support A and roller support B of the bridge truss are supported on concrete abutments. If the bearing failure stress of the concrete is (īai), – 4 ksi, determine the required minimum dimension of the square bearing plates at C and D to the nearest in. Apply a factor of safety of 2 against failure. 150 kip 100 kip B 200 kip 300 kip 300 kip 300 kip 300 kip F6 ft--6 ft--6 ft-6 ft--6 ft-|-6 ft-| Prob. 1–95

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(A) Determine all the forces of every member and identity members that can be solved by method of joints and method of sections. (B) Don't forget to solve the reactions, and to label the members if it's compression or tension. Please answer the problem in detailed solutions.
The singular force F will be applied to the kin with a hollow rectangular cross section. Accordingly, the location and value of the minimum normal stress that will occur in the whole beam is given correctly in the following? F-800 N. L1 - 4m, 12 - 1m, h1-48mm, h2 -72mm, b1-10mm, b2-20mm
Point B of the system given below is movable support and Enpoint is fixed bearing. According to the given loading condition a) Draw the normal force, moment and shear force diagrams. B) Check whether the section used between AB-BC-CD is suitable, as the material has normal allowable stress em = 85 Mpa and shear strength em = 50 Mpa. c) Find the diameter d of the section used between DE-EF since the normal allowable stress of the material is em = 85 Mpa and the shear strength is em = 50 Mpa.
SOLVE FOR THE FORCE IN MEMBERS AB, AC, BC, CD, BD, BE, DE, DF & EF. SHOW SOLUTIONS CLEARLY USING METHOD OF JOINTS AND WRITE WELL ALSO SEE LINK UNDER WEEK7 0.8m 2.4m -6KN MEMBER AB AC BC CD BD BE 2m ED DF EF 1m 8KN Av REACTION hinge) EX REACTION @roller) 3m SUMMARY OF RESULTS FORCE 1m 10KN 2.4m 3KN NATURE(I or C)
I need the answer as soon as possible
If the allowable shear stress for each of the 0.30-in.-diameter steel pins at A. B. and C is 13 ksi, and the allowable normal stress for the 0,40-in.-diameter rod BC is 22 ksi, determine the allowable uniform load w considering the allowable shear stress at A. Use a factor.of safety of 1.1. C 4 ft
For the given loaded truss, the allowable tensile stress in any member is up to 800 MPa while the allowable compressive stress is up to 650 MPa. The reduced stress in compression is specified to reduce the danger of buckling. Determine the minimum cross-sectional area of member CE. Solve with complete solution and proper FBD.
PLEASE SHOW COMPLETE SOLUTION. THANKS Determine the force in members GE, GC, and BC of the truss shown. Indicate whether the members are in tension or compression. Use method of sections.
The lap joint is fastened with four 3/16-in.-diameter rivets. The working stresses are 58 ksi for the rivets in shear and 10 ksi for the plates in bearing. in.
2. The lap joint is fastened with four 30-mm-diameter rivets. The working stresses are 84 MPa for the rivets in shear and 84 MPa for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets... 35 mm KATIN 160 mm
Plz
Present your solution and box your final answer