1-88 The boiling temperature of nitrogen at atmospheric pressure at sea level (1 atm) is -196°C. Therefore, nitrogen is commonly used in low temperature scientific studies since the temperature of liquid nitrogen in a tank open to the atmosphere will remain constant at -196°C until the liquid nitrogen in the tank is depleted. Any heat transfer to the tank will result in the evaporation of some liquid nitrogen, which has a heat of vaporization of 198 kJ/kg and a density of 810 kg/m³ at 1 atm. Consider a 4-m-diameter spherical tank initially filled with liquid nitrogen at 1 atm and -196°C. The tank is ex- posed to 20°C ambient air with a heat transfer coefficient of 25 W/m² °C. The temperature of the thin-shelled spherical tank is observed to be almost the same as the temperature of the nitrogen inside. Disregarding any radiation heat exchange, determine the rate of evaporation of the liquid nitrogen in the tank as a result of the heat transfer from the ambient air.

1-88 The boiling temperature of nitrogen at atmospheric pressure at sea level (1 atm) is -196°C. Therefore, nitrogen is commonly used in low temperature scientific studies since the temperature of liquid nitrogen in a tank open to the atmosphere will remain constant at -196°C until the liquid nitrogen in the tank is depleted. Any heat transfer to the tank will result in the evaporation of some liquid nitrogen, which has a heat of vaporization of 198 kJ/kg and a density of 810 kg/m³ at 1 atm. Consider a 4-m-diameter spherical tank initially filled with liquid nitrogen at 1 atm and -196°C. The tank is ex- posed to 20°C ambient air with a heat transfer coefficient of 25 W/m² °C. The temperature of the thin-shelled spherical tank is observed to be almost the same as the temperature of the nitrogen inside. Disregarding any radiation heat exchange, determine the rate of evaporation of the liquid nitrogen in the tank as a result of the heat transfer from the ambient air.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A machinist wishes to insert a brass rod with a diameter of 3 mm into a hole with a diameter of 2.998 mm. By how much would the machinist have to lower the temperature (in °C) of the rod to make it fit the hole?
The pressure in a steam boiler is given to be 92 kgf/cm2 . Express this pressure in psi, kPa, atm, and bars.
Unit of thermal conductivity in S.I. units is (a) J/m2 sec (b) J/m °K sec (c) W/m °K (d) (a) and (c) above (e) (b) and (c) above.
3. 100-gram oil at 20°C and 50-gram iron at 75 °C are placed in 200-gram iron container. The increase in temperature of the container is 5°C and the specific heat of oil is 0.43 cal/g °C. What is the specific heat of the iron?
1-53 The water in a tank is pressurized by air, and the pres- sure is measured by a multifluid manometer as shown in Fig. PI-53. Determine the gage pressure of air in the tank if h = 0.2 m, h, = 0.3 m, and h, = 0.46 m. Take the densities of water, oil, and mercury to be 1000 kg/m'. 850 kg/m, and 13.600 kg/m, respectively. Oil Aic Mercuty FIGURE P1-53 Scanned with CamScanner at a aeptn oI Y m. at uic UL 1-56 The absolute pressure in water at a depth of 5 m is read to be 145 kPa. Determine (a) the local atmospheric pres- sure, and (b) the absolute pressure at a depth of 5 m in a liq- uid whose specifc gravity is 0.85 at the same location. Neglectin eration, average 1-64 Scanned with CamScanner D FIGURE P1-58E 1-59 The piston diameters in Fig. Pl-58E are D, = 10 cm and D, = 4 cm. When the pressure in chamber 2 is 2000 kPa and the pressure in chamber 3 is 700 kPa, what is the pres-
Discussion What is heat capacity vs specific heat? What is specific heat of a liquid? Can the specific heat be negative? What is the specific heat of h20? How do I calculate specific heat? What is the symbol for specific heat? B2 R0 e o What has a higher specific heat than water?
4
1-53 The water in a tank is pressurized by air, and the pres- sure is measured by a multifluid manometer as shown in Fig. Pl-53. Determine the gage pressure of air in the tank if h = 0.2 m, hy = 0.3 m, and h, = 0.46 m. Take the densities of water, oil, and mercury to be 1000 kg/m', 850 kg/m, and 13,600 kg/m', respectively. Oil Aic Water Mercury FIGURE P1-53 Scanned with CamScanner at a deptn o1 Y m.
1-69E The pressure in a natural gas pipeline is measured by the manometer shown in Fig. P1-69E with one of the arms open to the atmosphere where the local atmospheric pressure is 14.2 psia. Determine the absolute pressure in the pipeline. Air 2 in Natural Gas 10 in 25 in 6 in Mercury SG = 13.6 Water
1-41 The ducts of an air heating system pass through an un- heated area. As a result of heat losses, the temperature of the air in the duct drops by 3°C. If the mass flow rate of air is 120 kg/min, determine the rate of heat loss from the air to the cold environment.