1-108 A pressure cooker cooks a lot faster than an ordinary pan by maintaining a higher pressure and temperature inside. The lid of a pressure cooker is well sealed, and steam can escape only through an opening in the middle of the lid. A separate metal piece, the petcock, sits on top of this opening and prevents steam from escaping until the pressure force overcomes the weight of the petcock. The periodic escape of the steam in this manner prevents any potentially dangerous pressure buildup and keeps the pressure inside at a constant value. Determine the mass of the petcock of a pressure cooker whose operation pressure is 100 kPa gage and has an opening cross-sectional area of 4 mm². Assume an atmo- spheric pressure of 101 kPa, and draw the free-body diagram of the petcock. Answer: 40.8 g Palm = 101 kPa air, and the as shown in in the tank if PRESSURE COOKER Petcock -A=4 mm²

1-108 A pressure cooker cooks a lot faster than an ordinary pan by maintaining a higher pressure and temperature inside. The lid of a pressure cooker is well sealed, and steam can escape only through an opening in the middle of the lid. A separate metal piece, the petcock, sits on top of this opening and prevents steam from escaping until the pressure force overcomes the weight of the petcock. The periodic escape of the steam in this manner prevents any potentially dangerous pressure buildup and keeps the pressure inside at a constant value. Determine the mass of the petcock of a pressure cooker whose operation pressure is 100 kPa gage and has an opening cross-sectional area of 4 mm². Assume an atmo- spheric pressure of 101 kPa, and draw the free-body diagram of the petcock. Answer: 40.8 g Palm = 101 kPa air, and the as shown in in the tank if PRESSURE COOKER Petcock -A=4 mm²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

can you solve d. - e. - f. and g. part
Q2:- Note: 1 Torr = 0.133 kPa & 1 atm 101.325 kPa (A) A spray metal bottle is used for polishing some Aluminum samples until it is empty. Then, the rest propellant gas inside the bottle has a pressure of 1344 torr at 23 °C. Finally, if the spray bottle is thrown into a fire at a temperature equals 475 °C. Determine the pressure in the hot bottle in kPa? Assuming no change in volume.
If the piston mass is 20 kg and the car mass with its base is 400 kg, what will the minimum pressure (kpa) that is required from the air compressor to lift the car? There are three layers of oils with different specific gravities as S1=0.95, S2-0.85, and S3-0.38. Neglect the shear force between the piston and its cylinder. Control valve - piston Air pressure from compressor 25-cm diameter 60 cm S3 S2 50 cm Air S1 40 cm S1 Lenovo K9 Note Al Dual Camera -12 DM
An open tank, with bottom dimensions of 7 x 9 meters, is 8 meters high. It has oil with specific gravity of 0.805 filling the tank up to the top. It is then accelerated upwards at 6.5 m/s2. Determine the resulting force (in kN) at the bottom of the tank during acceleration
The component of the force along the inclined plane due to mass of the body on a inclined plane is 100N. The net force acting on the body is 60N.The force of friction is Select one: O 160 N O 40 N O 1.67 N O 0.6 N
10
1-109E Consider a U-tube whose arms are open to the atmosphere. Now equal volumes of water and light oil (p 49.3 lbm/ft') are poured from different arms. A person blows from the oil side of the U-tube until the contact surface of the two fluids moves to the bottom of the U-tube, and thus the liquid levels in the two arms are the same. If the fluid height in each arm is 30 in, determine the gage pressure the person exerts on the oil by blowing. -Air Oil Water 30 in FIGURE P1-109E
The piston of a vertical piston-cylinder device containing a gas has a mass of 50 kg and a cross- sectional area of 0.04 m2, as shown in the figure. The local atmospheric pressure is 0.97 bar, and the gravitational acceleration is 9.81 m/s². What is the pressure inside the cylinder?
A machinist wishes to insert a brass rod with a diameter of 3 mm into a hole with a diameter of 2.998 mm. By how much would the machinist have to lower the temperature (in °C) of the rod to make it fit the hole?
1 For the car lift shown in the figure, determine the force required to be applied (F1), for the following cases: (i)A1 = 0.1 m2 and A2 = 0.25 m2 (ii)A1 = 0.05 m2 and A2 = 0.25 m2 Take mass of the car as 1500 kg.
A spring exerts a force of 17 lbf on a piston inside a piston cylinder device. The mass of the piston is 3.5 lbs and the cross sectional area of it is 0.00018 ft^2. Determine the pressure inside the piston cylinder device.
The pressure inside a competion grade tennis ball is 1.6 times higher than the atmospheric pressure. The diameter and wall thicknwess of the tennis is 66 mm and 2.8 mm, respectively. Considering the atmospheric pressure as 100,000 Pa, determine the stress in the tennis ball at rest. Express the result in MPa with 2 decimal points.