SNo.1234Prepare the lead statement and total cost for the following materialsAssume for Metal Track -Lead x 1, Carts Track-Lead x 1.1, and S.Track-Lead x 1.4Lead in KMMaterialsRate at Source MetalTruckCarts SandyTruck TruckConveyanceChargé per KM$80/m³10.50.8$0.3/m²$160/1000Nos0.80.5$7/1000Nos./km$6/m³0.671($1.9/Km/m³$26/m³0.70.9$1.4/Km/m²"CementBrickSandGravel 40mmwww0.350.314Toll Charge$2$6/1000Nos$1ANEVELRETaxesCharges$3$3/500NOS$2

This question is related to estimation and Costing. We have the 4 materials given in the tabular…

1 2 3 S No. 4 Prepare the lead statement and total cost for the following materials Assume for Metal Track -Lead x 1, Carts Track-Lead x 1.1, and S. Track-Lead x 1.4 Lead In KM Materials Rate at Source Metal Truck Conveyance Chargé per KM Carts Sandy Truck Truck 0.5- $80/m³ 1 0.8 $0.3/m³ $7/1000Nos./km $160/1000Nos 0.8 0.5 ********** $6/m³ 0.67 0.35 1 ($1.9/Km/m³ $26/m³ 0.7 0.3 0.9 $1.4/Km/m² "Cement Brick Sand Gravel 40mm Toll Charge $2 $6/1000NOS $1 ******** Taxes Charges $3 $3/500NOS $2 *********

1 2 3 S No. 4 Prepare the lead statement and total cost for the following materials Assume for Metal Track -Lead x 1, Carts Track-Lead x 1.1, and S. Track-Lead x 1.4 Lead In KM Materials Rate at Source Metal Truck Conveyance Chargé per KM Carts Sandy Truck Truck 0.5- $80/m³ 1 0.8 $0.3/m³ $7/1000Nos./km $160/1000Nos 0.8 0.5 ** $6/m³ 0.67 0.35 1 ($1.9/Km/m³ $26/m³ 0.7 0.3 0.9 $1.4/Km/m² "Cement Brick Sand Gravel 40mm Toll Charge $2 $6/1000NOS $1 Taxes Charges $3 $3/500NOS $2 *

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

needed asap pls, thank you
Hazen-Williams formula was used in the derivation. 2- Explain why the Aluminum sulfate (alum) is widely used as a c 1-What are the factors allecting coagulation. b-Prove that the value of the exponent x in the relation (h=kQ) is 1.85 when Q5: distinguish its occurrence? a-Explain why cavitation oecurred in pumps and how one can icoagulant.
Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained:Volume of bucket = 14 LWeight of empty bucket = 9.21 kgWeight of bucket filled with dry rodded coarse aggregate:Trial 1 = 34.75 kgTrial 2 = 34.06 kgMeasureSampleA B CWet Mass (g) 521.0 522.4 523.4Dry Mass (g) 491.6 491.7 492.1Absorption (%) 2.5 2.4 2.3Table P 5 . 9 determine the amount of water required to increase the moisture content of aggregate to reach absorption?5.9 Three samples of fine aggregate have the properties shown in Table Trial 3 = 35.74 kga. Calculate the average dry-rodded unit weightb. If the bulk dry specific gravity of the aggregate is 2.620, calculate thepercent voids between aggregate particles for each trial.
Concrete is the second most used material on earth next to water and it is approximately 80% aggregates. Aggregates are best used for concrete because it is cheap, abundant and inert. However, some places experience aggregate shortages because of isolation and dependence to natural aggregates. According to a research 2020 the 3d common cost of construction delays on road projects is "non-issuance of permit for extraction of aggregates". This extraction suspension is applied to curb the use of natural aggregates and provide time for rivers to replenish its aggregate supply. As a future civil engineer, what should our agencies do? What innovative ideas can we implement to help mitigate aggregate shortages?
. Determin the max aggregate size (MAS) and nominal aggregate size (NMAS) for the folwong gradation Sieve size, mm % passing 25.5 19 100 100 16 92.3 9.5 12.5 88.6 55.5 4.75 46 2.36 33 1.18 25.7
n h t's Inital Initial | Final EDTA Sample EDTA 2 moles ESTA Volume Ca²+ and Volume Volume Volume Used Mg²+ 100 me 25.0 me 22.9 me 3.1 me 2+ 100 me 25.0 me 21.5m 3.5m 100 me 25.0ml 23.8 me 2.2 m² Sample Water 4 2 3 For each titration: Hardness (ppm) Calculate the average hardness and calculate the standard deviation of your data show sample calculations.
Compute it manually
Any help please?
13. A contractor needs 375 m³ of aggregate base for a highway construction project. It will be compacted to a dry unit weight of 18.9 kN/m³. This material is available in a stockpile at a local material supply yard at a water content of 7.75%, but is sold by the metric ton and not by cubic meters (ton 3 1000kg). a. How many tons of aggregate should the contractor purchase? Round your answer to the nearest whole number. b. A few weeks later, an intense rainstorm increased the water content of the stockpile to 14%. If the contractor orders the same quantity for an identical section of the highway, how many cubic meters. of compacted aggregate base will he produce?
Material Specific Gravity Weight (g) Bulk specific gravity Coarse 2450 2.69 Aggregate Fine 1270 2.58 Aggregate Filler Asphalt 120 2.47 1.05 4% cement
A 32-cy wheel loader will be used to load trucks from a quarry stockpile of processed aggregates having a maximum size of in. The haul distance will be negligible. The aggregate has a loose unit weight of 2,900 lb/cy. Estimate the loader production in tons based on a 50-min-hour efficiency factor. Use an aggressive cycle time and fill factor.
5