06. The lap joint is connected by three 20-mm diameter rivets. Assuming that the axial load P = 50 kN is distributed among the three rivets, find a. the shear stress in each rivet; b. the bearing stress between the plate and a rivet; the maximum average tensile stress in each plate. С. Express your answer in MPa 130 mm O O O 3/4 25 mm 25 mm

06. The lap joint is connected by three 20-mm diameter rivets. Assuming that the axial load P = 50 kN is distributed among the three rivets, find a. the shear stress in each rivet; b. the bearing stress between the plate and a rivet; the maximum average tensile stress in each plate. С. Express your answer in MPa 130 mm O O O 3/4 25 mm 25 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The axial load 343 kN applied to the lap joint is distributed equally among the three 16-mm-diameter rivets. What is the maximum tensile stress (in MPa) in the plate if w = 135.3mm and t = 28.5mm? Round off the final answer to three decimal places. 020 bearing.png ... t t P P
The boom AC is a 4-in. square steel tube with a wall thickness of 0.30 in. The boom is supported by the 0.65-in .-diameter pin at A, and the 0.45-in .-diameter cable BC. Neglecting the weight of the boom, determine the tensile stress in the cable (in psi) if P = 4490 lb. Round off the final answer to three decimal places.
A cantilever beam is subjected to an inclined force (P) as shown in Figure 1, the equilibrium normal force component on the cross- sectional area at the point A is (in kN) Figure 1: P 400 kN 30 1000 mm A Area 30 mm 20 mm
The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the pin in psi if a load of P = 19616 lb is applied at A? The d = 0.65-in.-diameter pin is in double shear. Round off the final answer to two decimal places.
A steel bolt has a diameter of 8 mm. The bolt is encased by a bronze tube that has an outer diameter of 15 mm and inner diameter of 8 mm. A force is applied to the bolt. F d3 d1 F Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value F₁ 25 kN Esteel 200 GPa Ebronze 105 GPa a. Determine the magnitude of the normal force in the steel bolt, Nsteel. b. Determine the magnitude of the normal force in the bronze tube, Nbronze. c. Determine the magnitude of the normal stress in the steel bolt, σsteel. d. Determine the magnitude of the normal stress in the bronze tube, σbronze Round your final answers to 3 significant digits. Nsteel = KN Nbronze = KN σ steel = MPa MPa Obronze
A pipe with an inside diameter of 42 mm is subjected to an axial load of 850 kN. If the maximum allowable tensile stress in the pipe is 2.50 kN/mm², calculate the minimum wall thickness required for the pipe. Give your answer in millimetres (mm) to 2 decimal places.
The lap joint is fastened with four 0.79-in.-diameter rivets. The working stress is 17.27 ksi for the rivets in shear. Find the axial load P (in lb) that can be applied to the joint. Assume that the load is equally distributed among the rivets. Round off the final answer to two decimal places.
1.19 Find the stresses in members AB, BC , and CD for the truss shown. Indicate tension or compression. The cross-sectional area of each member is 1600 mm². В 3 m 3 m 4 m E A C 40 kN 70 kN 4 m F
Determine the compressive force (in Ib) in the bars shown after a temperature rise of 149°F if d = 0.012 in. Round off the final answer to five decimal places. d ... L M Use the following data: Bronze Aluminum A = 2.24 sq. in A = 2.73 sq. in E = 14930924 psi L = 13.4 in E = 10543748 psi L= 16 in a = 11.76 x 10-6/ °F a = 12.54 x 10-6/°F
If the block is loaded with P = 257 kN, calculate the required dimension "h" of the key. Write your final answer in 2 decimal places with the unit of mm.
The T-section in the figure was created by gluing two rectangular wooden planks of 18 cm in size with glue. Since the glue value of the shear force affecting the section is Ty = 10KN, determine what the minimum safety stress of the glue should be in order to ensure joint security. (Ix = 11016 cm ^ 4) Write the result after the comma, rounding it to two decimal places and specifying. 18cm T. бст tutkal 18cm Y1Scm 6cm
1.85 help