0404040 0000 K x(1) f(1

Q: Find the steady-state error of this system when a unit-step input is applied. R(s) 9 3 + 1 C(s) S+ 9…

A:

Q: The figure below shows the block diagram of a dc-motor control system. The signal N(s) is the torque…

A: Given a transfer function H(s) so that the output Y(s) is not affected by N(s)

Q: The open-loop transfer function of a unity feedback system is given by G (s) = 5000 s(s+80s)

A:

Q: Derive the relationship between output, the p.d. across the capacitor, and the input v R CH Sketch…

A: The given circuit is We need to determine the relationship between the output, the potential…

Q: t-o IF ve? Ve lt) -9

A:

Q: Problem 2 Define the initial current , the final current ly, the time constant r, and the current i…

A:

Q: 25 a. Given the transfer function G(s) = , evaluate the percent overshoot, settling s²+4s+25' time,…

A: Given transfer function  G(s)=25s2+4s+25

Q: I hope you can clarify how to draw a small triangle accurately.

A: Step 1:The transconductance (gm) of a JFET can be calculated using the following formula: gm = 2…

Q: Using Nyquist criterion, how many open loop poles are in the right half plane in the given system…

A: given control system

Q: We are now interested in studying the behavior of the rotating valve plate shaft on an ETC only.…

A:

Q: 4) The number of zeros on the RHP of the system whose step response is shown in Figure 2 is

A: The poles and zeros are very important in determining the stability of the system. So the Numerator…

Q: Problem 3. For the given system, find gain K that can make the steady-state error about 5% for a…

A:

Q: Q9 The discrete-time signals x1[n] is shown in the figure. Carefully sketch each of the following…

A:

Q: The function F(A, B, C, D) shown in the Figure can be simplified to: Note: o is XNOR symbol (Ao B) +…

A:

Q: s(s+3)(s+5)* K açılarını, asimptotlanın kesişim noktalarını bulunuz. Kök-Yer eğrisinin sanal ekseni…

A:

Q: B- Obtain a signal flow graph to represent the following set of algebraic equations: X, = R-X3, X2 =…

A:

Q: The system shown in the given figure relates temperature control of air flow. Equation of heat…

A: Given- Equation of heat exchanger = 10dTAdt+TA=u, Temperature sensation equation =2dTsdt+Ts=TA,   To…

Q: itegral s Rdr y Fram Evaluate the where R2 = xt porial P(3,4 } fa) along the duied path op (b)alang…

A:

Q: 5. a. Convert the following expressions into a sum-of-products (SOP) form: (A +B)(C+B) (A +BC)C b.…

A:

Q: Problem 2 (3 points): For the system of Figure 2, apply the Routh-Hurwitz Criterion to tell how many…

A:

Q: The question concearns RLC circuit, i have 2 sets of data, I need to calculate Z (impedance), R…

A:

Q: Z6 ( RL parallel ) 132 50 0,5 0,66 184 86

A: Resistance can be calculated as, Impedance can be calculated as,

Q: A motor whose torque-speed curve is Tm= -0.5wm+50 when the input voltage is ea-10 V, drives the load…

A: Given, Torque speed curve, Tm=-0.5ωm+50Input voltagae, ea=10VJ1=3kg-m2J2=7 kg-m2D=2…

Q: Ql For Flip sR the equation is 'Not QLQ)' ise- a) R+s'Q' b) S+ RQ' c) s'+R'Q D) R'ts' Q

A: We need to find out compliment of Output of SR flip flop

Q: Q23 answer required only

A: To solve above problem one should know about SOP and POS form of Boolean expression. In POS form,…

Q: The following signal has: - To x(t) A - A To 4 To 2 To 1. Complex coefficients with even symmetric…

A: Given a periodic signal, we need to determine the Fourier series coefficients.

Q: Q2) Find k and for the system shown in Figure 2 by using = 0.5 and steady-state error (ess) = 0.3…

A: We need to find out the unknown for given system .

Q: A CT system with the poles s1=-1 and s2=0.7-j2 is NOTE: write one of the following words:…

A: Given: s1=-1 s2=0.7-j2 For stability , all the poles should should lie in left half of s plane . If…