Q4 Example 3.5A U-tube manometer similar to that shown in Figure 3.8 is used to measure the gaugepressure of a fluid P of density p= 1000 kg/m. If the density of the liquid Q is 13.6 x10° kg/m, what will be the gauge pressure at A if h; = 0.15 m and h2 = 0.25 m aboveBC. Take into consideration patm = 101.3 kN/m.Fluid PFigure 3.8Solution to Example 3.5Putting,PQ = 13.6 x103Pp = 1000 kg/mhi = 0.15 mh2 0.25 m

Answered: Image /qna-images/answer/d52e010b-cfac-4842-8cb4-671bd67adaaa.jpg

Answered: 04 Example 3.5 A U-tube manometer…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The differential change in pressure p close to the surface of a static fluid is given by the following expression:dp/dy = -3Ap2,where A is a constant, with units of 1/(atm•m), and p is the pressure in atm. The pressure at the surface of the fluid is p(0) = 1 atm, and the coordinate y here is positive upwards with origin at the surface. An absulute pressure gauge is placed at a depth 0.19m in the fluid. What would be the reading of the pressure gauge in units in atm? you can take the constant A=1(atm.m)^-1
READ CAREFULLY !! > ROUND OFF/UP YOUR ANSWERS TO 4 DECIMAL PLACES. INCLUDE ALL THE NECESSARY UNITS. <
A "dead-weight" pressure testing machine as shown in Fig. Q5b is used to measure the accuracy of a Bourdon pressure gauge. If the weight and piston together weigh 200 N and the piston diameter is 2.5 cm, find the percentage error of the Bourdon pressure gauge if it indicates a pressure of 350 kPa. Piston weight Fig. Q5a oil Pressure gauge [3 marks]
The figure shows a sensor indicating a gauge pressure reading of 1.5 kPa. The fluids are at 20°C Determine: a) the height hb. b) the height hc.The specific weight of air is 12.0 N/m3.
Suppose a gas-filled incandescent light bulb is manufactured so that the gas inside the bulb is at atmospheric pressure (1 atm = 1.013 × 105 Pa) when the bulb has a temperature of 20.0 °C. Find the gauge pressure inside such a bulb when it is hot, assuming its average hot temperature is 75.0 °C. gauge pressure when hot: 1.87 X104 Incorrect The actual final pressure of the light bulb will be different than calculated in the first question because the glass bulb will expand. What will the final actual gauge pressure be, taking this into account? The volume expansion coefficient for glass is ß = 2.700 x 10-5 °C-1. final gauge pressure, accounting for glass expansion: 1.20 ×105 Pa Incorrect Pa
C1 (a). A lubricating oil having the dynamic viscosity of 0.056 poise and specific gravity of 1.17. Calculate (i) the density of oil in kg/m3, (ii) the weight density of oil in N/m3, (iii) the kinematic viscosity in stokes, and (iv) the specific volume in m3/kg. C1 (b). The capillary effect in a glass tube of 2.8 mm diameter, when immersed in (1) water and (2) mercury are 7.7 mm and -3.5 mm respectively. Calculate the value of surface tension in contact with air for water and mercury in N/m. Take, the contact angle for water =0° and mercury =130°. C1(a). (i).the density of oil in kg/m3 C1(a). (ii) the weight density of oil in N/m3 C1(a). (iii) the kinematic viscosity in stokes C1(a). (iv) the specific volume in m3/kg C1 (b). 1.the value of surface tension (water) in N/m C1 (b). 2. the value of surface tension (mercury) in N/m
I need the answer as soon as possible
Dynamic viscosity of fluid Density of fluid If X= , then the unit of X is = O m?/kg O m/sec? O m/sec O m?/sec The container contains an oil of specific gravity 0.64 with the pressure measured at the bottom of the container is 150 Pa. Find the pressure head in m of oil. The pressure head of oil in m = If the density of fluid is not a variable in a fluid flow, it is known as O Incompressible O Unsteady flow O Uniform flow O Compressible
Q5: The compart ments (8) 4 C) in figure below are closed & filled with air. When the gauges (A) 4 (D) read as indicated, what should be the value of Cx) for gaugeCE)? (Mereury in each U-tube gauge) 2.07 bar 254 Air Air E x
I need a fast solution
Fluid Statics Please provide a complete and readable solution for the problem if necessary and an explanation. Thank you!
Compute the pressure difference between m and n, in pounds per square inch, when: a) Fluid A is brine (sp gr 1.15), the gage fluid is oil (sp gr 0.92), and z = 49.69 in.b) Fluid A is water, the gage fluid is air, and z = 19.69 in.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS