Answered: ○ 0,331 kg ○ 0,440 kg ○ 0,549 kg ○…

Engineering

Mechanical Engineering

○ 0,331 kg ○ 0,440 kg ○ 0,549 kg ○ 0,648 kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Vibrations please help
Find the maximum vertical acceleration of the floor of a truck trailer, in g, if the suspension frequency is 7 Hz and the floor exhibits a single amplitude vertical displacement of 4 cm.
9. Vibration of water in a tube. If 1 liter of water (about 1.06 US quart) is vibrating up and down under the influence of gravitation in a U-shaped tube of diameter 2 cm (Fig. 44), what is the frequency? Neglect friction. First guess. ул (y = 0) Fig. 44. Tube (Problem 9)
A certain stress sensor is mounted on an aircraft wing that is subject to periodic wing gusts. The stress can be approximated by a sinusoidal function (i.e. sine wave) with an average 2,381 kPa and amplitude 112 at a frequency of 6 Hz. Determine the maximum stress value in kPa. (Provide the answer using 2 decimal places).
A mechanical system is presented as below. There are four simulation graphs for different values for m, b and c tested for a step response. Identify the graph for m=4 kg, b=0.3 N.s/m and k=1 N/m (Hint: you may need to use matlab simulation to find it). m 1.8 1.6 1.4 b ·f(t) Step Response
Select the right answer for each of the following: 1- The damped vibrational system is. system, (c) none of these, (d) false statement. (a) conservative system, (b) nonconservative (a) viscous (b) solid 2- When a system vibrates in a fluid medium, the damping is (c) Coulomb. 3- When an initial excitation exerted on a vibrational system results in - ippearance. (a) natural frequency. (b) resonance. (c) beating. (d) none of these. 4- Undamped vibration is characterized by no loss of 1) (a) speed, (b) acceleration, (c) mass, (d) energy. (a) mass, (b) damper, 5- Vibratory system should at least consists of a spring and - (c) mass and damper.
a) In periodic motion, it is often interesting to investigate the harmonic motion of an object. The decrease in amplitude caused by dissipative force is called damping, and the corresponding motion is called damped oscillation. Damped oscillation is governed by the following equation, where is the angular frequency of oscillation, A is the initial amplitude of the oscillation, m is the mass of an object, b is a constant that describes the strength of the damping force, t is time in seconds, h is the ratio between a force constant k and the mass m: where x(t) = Ae sin(at + p) If = 60°, A = 4, v = 2m @= h b² 4m² b = 0.25, create a plot x(t) for 0≤t≤ 15, with h = 4. Label all the axes, 2m include gridlines and provide a title in your plot.
A force of F = 50 N is applied to the rope that causes the angle 0₁ = 60 degrees to keep the system at equilibrium. The N spring constant is k = 100 m B a 0₁ с a b с Variable Value 2 m 2 m 2 m F b Values for the figure are given in the following table. Note the figure may not be to scale. cc i❀O BY NC SA 2013 Michael Swanbom
According to Hooke's Law, we need to be measuring x (the length of the spring) however our CBR is set up to measure y( the height of the bottom of the mass). Create a diagram and explains why we can swap out x variables for y variables when conducting this experiment x y
You are determining the period of oscillation of a pendulum. One procedure would be to measure the time for 20 oscillations, t20, and repeat the measurement 5 times. Another procedure would be to measure the time for 5 oscillations, t5, and repeat the measurement 20 times. Assume, reasonably, that the error in the determination of the time for 20 oscillations is the same as the error in the determination of the time for 5 oscillations. Calculate the error in the period for both procedures to determine which will give the smallest error in the value of the period? Comments on your answer.
please be specific and explain will up vote if correct
Three engineers are independently estimating the spring constant of a spring, using the linear model specified by Hooke’s law. Engineer A measures the length of the spring under loads of 0, 1, 2, 4, and 6 lb, for a total of five measurements. Engineer B uses the same loads, but repeats the experiment twice, for a total of 10 independent measurements. Engineer C uses loads of 0, 2, 4, 8, and 12 lb, measuring once for each load. The engineers all use the same measurement apparatus and procedure. Each engineer computes a 95% confidence interval for the spring constant. If the width of the interval of engineer A is divided by the width of the interval of engineer B, the quotient will be approximately _____. Numeric Response