030 Print Reading for Industry Class Date Name Industry Print Exercise 14-2 Refer to the print PR 14-2 and answer the questions below. 1. What are the three columns of the revision history block of this drawing? 2. What revision letter/item number is assigned to the addition of datum W? used to be. 3. Revision A9 is floating next to an empty space where Revision A6 added a triangle and a feature control frame. What does the triangle mean? 5. What revision letter and item number is assigned to the material specification? 6. In what zone is revision A2 located? 7. What type of pin is referred to in revision A1? 8. What change was made in revision A8? Review questions based on previous units: 9. What is the name of this part? 10. How many general notes are shown on this print? 11. If not specified, what is the tolerance for a three-place decimal value? 12. Are there any surface texture symbols shown? 13. What is the maximum material condition diameter of the main central hole? 14. At what scale is the enlarged view? 15. What four geometric tolerances are invoked on this drawing? PROPRIETARY DATA HEREIN IS PROPRIETARY TO SKIL CORP. AND SHALL NOT BE USED OR DISCLOSED IN WHOLE OR PART FOR ANY PURPOSE WHATEVER WITHOUT SKIL CORP. PRIOR APPROVAL PART THE DATA CONTAINED ON PRE-RLS DIST 619 -2X.187 EJECTOR PINS FLUSH TO .005 BELOW SURFACE 3000 PART NO. PEO.2397.904706.FLANGE-INNER SKIL CORPORATION SUBSIDIARY OF EMERSON ELECTRIC CO. CHICAGO, ILLINOIS 1.30 WITNESS LINE PART MAME FLANGE-INNER 1.0 MATERIAL SPECIFICATION: .685 MATERIAL SEE CHART .005 XM MPIF # FN-0405-130HT MATERIAL 1.1 HEAT TREAT SEE CHART A A HSN PER SKL SID CENDS DRAWN APPROVED H.L 6.8 GRAMS/CC MIN 92 DENSITY NNO 1.2 12-23 PED 2397 3-16 3-18 12-23 RLS. 4-2 SCALE 21 APPARENT HARDNESS RC 30-45 (SEE NOTE 3.5) REVISIONS 1.3 PRC JON N 2-15 REVD. GEOMETRIC TOL ADDED NOTE 3.6 $1 F-2 D.828+.003 000 .001 MZM PRC JON N. 3-16 $2 ADDED HARDNESS NOTE A-2 REVISED NOTE 1.8 PEC 40548 JON N. ADD 2x .187 EJECTOR PINS 9-3 X A1 FLUSH TO .005 BELOW SURFACE C-8 BV 2.0 INSPECTION SPECIFICATION: ADD 92 DIM A-7 ADD $1.30 WITNESS LINE D-8 ADD DATUM W E-3 10,000 POUNDS MIN (SUPPORT PART ON SURFACE W AND APPLY COMPRESSIVE LOAD TO SURFACE Y.) AXIAL CRUSH STRENGTH TEST 2.1 D-5 A5 *-TO BE DETERMINED BY VENDOR AND SKIL ENG. O002 WAS 0025 YZ D-2 1.650- HEAT TREAT PARTICLE HARDNESS REVISED INSPECTION SPECS. G-8 FIXTURE NO AND LOAD RATE TBD -01.460- G-5 AB EACH LOT SKIL INSPECTION OMIT NOTE 3.6 RUNOUT-FT.LBS F-2 2.2 TO CHECK: 1.150- .080 -.155 R.005 MAX.- .370 30 3.0 GENERAL NOTES: 010- .020 R.030 3.1 VENDOR TO CERTIFY MATERIAL AND HEAT TREATMENT WITH EACH LOT AS PER PRINT. 040- 080 3.2 SKIL ENG. DEPT. TO APPROVE FIRST SAMPLES PRIOR 015- TO FULL PRODUCTION OR ANY CHANGE IN MATERIAL SPECIFICATION BY THE VENDOR. .002 629 .626 3.3 DIP IN RUST PREVENTATIVE OIL APPARENT HARDNESS 2 TO BE MEASURED ON THIS FACE 3.4 ALL SURFACES TO BE CLEAN AND FREE OF ALL CARBON RESIDUE, EXCESSIVE OXIDATION OR FOREIGN MATERIAL .8748 8720 3.5 APPARENT HARDNESS TO BE MEASURED ON HUB FACE. 1.100- -,010 1.560) 1.560- = CRITICAL CHARACTERISTIC ENLARGED VIEW SCALE= 10X REFER TO ANSI Y15.5M 1982 FOR GEOMETRIC DIMENSIONING STANDARDS SECTION A-A LIMITS UNLESS OTHERWISE SPECIFIED X-.010 XXX-.005 REMOVE ALL BURRS ANGULAR DIM.-1 K H 9 2 * 2 2 007 Print supplied by Skil Corporatior PR 14-2. Inner Flange
030 Print Reading for Industry Class Date Name Industry Print Exercise 14-2 Refer to the print PR 14-2 and answer the questions below. 1. What are the three columns of the revision history block of this drawing? 2. What revision letter/item number is assigned to the addition of datum W? used to be. 3. Revision A9 is floating next to an empty space where Revision A6 added a triangle and a feature control frame. What does the triangle mean? 5. What revision letter and item number is assigned to the material specification? 6. In what zone is revision A2 located? 7. What type of pin is referred to in revision A1? 8. What change was made in revision A8? Review questions based on previous units: 9. What is the name of this part? 10. How many general notes are shown on this print? 11. If not specified, what is the tolerance for a three-place decimal value? 12. Are there any surface texture symbols shown? 13. What is the maximum material condition diameter of the main central hole? 14. At what scale is the enlarged view? 15. What four geometric tolerances are invoked on this drawing? PROPRIETARY DATA HEREIN IS PROPRIETARY TO SKIL CORP. AND SHALL NOT BE USED OR DISCLOSED IN WHOLE OR PART FOR ANY PURPOSE WHATEVER WITHOUT SKIL CORP. PRIOR APPROVAL PART THE DATA CONTAINED ON PRE-RLS DIST 619 -2X.187 EJECTOR PINS FLUSH TO .005 BELOW SURFACE 3000 PART NO. PEO.2397.904706.FLANGE-INNER SKIL CORPORATION SUBSIDIARY OF EMERSON ELECTRIC CO. CHICAGO, ILLINOIS 1.30 WITNESS LINE PART MAME FLANGE-INNER 1.0 MATERIAL SPECIFICATION: .685 MATERIAL SEE CHART .005 XM MPIF # FN-0405-130HT MATERIAL 1.1 HEAT TREAT SEE CHART A A HSN PER SKL SID CENDS DRAWN APPROVED H.L 6.8 GRAMS/CC MIN 92 DENSITY NNO 1.2 12-23 PED 2397 3-16 3-18 12-23 RLS. 4-2 SCALE 21 APPARENT HARDNESS RC 30-45 (SEE NOTE 3.5) REVISIONS 1.3 PRC JON N 2-15 REVD. GEOMETRIC TOL ADDED NOTE 3.6 $1 F-2 D.828+.003 000 .001 MZM PRC JON N. 3-16 $2 ADDED HARDNESS NOTE A-2 REVISED NOTE 1.8 PEC 40548 JON N. ADD 2x .187 EJECTOR PINS 9-3 X A1 FLUSH TO .005 BELOW SURFACE C-8 BV 2.0 INSPECTION SPECIFICATION: ADD 92 DIM A-7 ADD $1.30 WITNESS LINE D-8 ADD DATUM W E-3 10,000 POUNDS MIN (SUPPORT PART ON SURFACE W AND APPLY COMPRESSIVE LOAD TO SURFACE Y.) AXIAL CRUSH STRENGTH TEST 2.1 D-5 A5 *-TO BE DETERMINED BY VENDOR AND SKIL ENG. O002 WAS 0025 YZ D-2 1.650- HEAT TREAT PARTICLE HARDNESS REVISED INSPECTION SPECS. G-8 FIXTURE NO AND LOAD RATE TBD -01.460- G-5 AB EACH LOT SKIL INSPECTION OMIT NOTE 3.6 RUNOUT-FT.LBS F-2 2.2 TO CHECK: 1.150- .080 -.155 R.005 MAX.- .370 30 3.0 GENERAL NOTES: 010- .020 R.030 3.1 VENDOR TO CERTIFY MATERIAL AND HEAT TREATMENT WITH EACH LOT AS PER PRINT. 040- 080 3.2 SKIL ENG. DEPT. TO APPROVE FIRST SAMPLES PRIOR 015- TO FULL PRODUCTION OR ANY CHANGE IN MATERIAL SPECIFICATION BY THE VENDOR. .002 629 .626 3.3 DIP IN RUST PREVENTATIVE OIL APPARENT HARDNESS 2 TO BE MEASURED ON THIS FACE 3.4 ALL SURFACES TO BE CLEAN AND FREE OF ALL CARBON RESIDUE, EXCESSIVE OXIDATION OR FOREIGN MATERIAL .8748 8720 3.5 APPARENT HARDNESS TO BE MEASURED ON HUB FACE. 1.100- -,010 1.560) 1.560- = CRITICAL CHARACTERISTIC ENLARGED VIEW SCALE= 10X REFER TO ANSI Y15.5M 1982 FOR GEOMETRIC DIMENSIONING STANDARDS SECTION A-A LIMITS UNLESS OTHERWISE SPECIFIED X-.010 XXX-.005 REMOVE ALL BURRS ANGULAR DIM.-1 K H 9 2 * 2 2 007 Print supplied by Skil Corporatior PR 14-2. Inner Flange
Elements Of Electromagnetics
7th Edition
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Sadiku, Matthew N. O.
ChapterMA: Math Assessment
Section: Chapter Questions
Problem 1.1MA
Related questions
Question
I need answers for questions 1, 2, and 3, pertaining to the print provided.
Expert Solution
This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
Step by step
Solved in 3 steps with 1 images
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Recommended textbooks for you
Elements Of Electromagnetics
Mechanical Engineering
ISBN:
9780190698614
Author:
Sadiku, Matthew N. O.
Publisher:
Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:
9780134319650
Author:
Russell C. Hibbeler
Publisher:
PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:
9781259822674
Author:
Yunus A. Cengel Dr., Michael A. Boles
Publisher:
McGraw-Hill Education
Elements Of Electromagnetics
Mechanical Engineering
ISBN:
9780190698614
Author:
Sadiku, Matthew N. O.
Publisher:
Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:
9780134319650
Author:
Russell C. Hibbeler
Publisher:
PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:
9781259822674
Author:
Yunus A. Cengel Dr., Michael A. Boles
Publisher:
McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:
9781118170519
Author:
Norman S. Nise
Publisher:
WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:
9781337093347
Author:
Barry J. Goodno, James M. Gere
Publisher:
Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:
9781118807330
Author:
James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:
WILEY