03: A wire 10m long of cross section area 1.22 cm' olongatos by 1.5 cm when 4.5 kg is suspended from it find: 1. Stress 2. Strain 3. Youngs modulus of the wire

Q: A thin rectangular plate is uniformly, deformed, as shown. Determine the shear strain Yxy at P.…

A: Solution: The shear strain of the thin rectangular sheet in the y-direction can be obtained using…

Q: When an axial load is applied to the ends of the bar shown in the figure, the total elongation of…

A: Given Elongation of the bar between A dan C δtotal = 0.22 in Strain ε2…

Q: 6. Consider a long wire of cross-sectional area A, initial length Lo, and extension of the wire AL.…

A: According to question we need to define young modulus.

Q: A 215-kg load is hung on a wire of length of 4.60 m, cross-sectional area 2.00 x 10 m2, and Young's…

A:

Q: Assume a hand has a 1.4m shaft of bone with an average cross-sectional area of 3 [cm] ^2. What is…

A:

Q: A wooden dowel is subjected to a shearing force of 715N on its top cylindrical face. If the dowel…

A: Shearing force F=715 N, diameter of dowel d=3cm (radius r=1.5cm), height of dowel h=11 cm and shear…

Q: A 195-kg load is hung on a wire of length of 4,30 m, cross-sectional area 2.00 x 10 5 m2, and…

A: Givenm=195 kgL=4.3 mA=2×10-5 m2Y=8×1010 N/m2

Q: A copper wire of length 6.7 m , cross sectional area 3.2 x 10--m²and Young's modulus 11 x 1010 N/m²…

A: Length of wire L = 6.7 m Cross-sectional area A = 3.2 × 10- 6 m2 Young modulus Y = 11 × 1010 N/m2…

Q: A copper wire of length 8.7 m , cross sectional area 1.3 x 10-6m2and Young’s modulus 11 x 1010 N/m2…

A:

Q: A liquid compressed in a container has a volume of 2 liters at a pressure of2MPa and a volume of…

A: Elasticity is the elongation or stretch of a material when a force is applied in the discipline of…

Q: A copper wire of length 5.9 m , cross sectional area 2.6 x 10-6m2and Young’s modulus 11 x 1010 N/m2…

A:

Q: 1. A cubic-shaped elastic block with side length L = 50 cm is fixed to the floor. An external force…

A: To solve this problem, we'll approach each part step by step.Part (a) Determine the angle ϕThe angle…

Q: A copper wire of length 7.9 m , cross sectional area 2 x 10-m²and Young's modulus 11 x 1010 N/m² has…

A:

Q: Question 12 The shear modulus of aluminum is 2.40×10¹0 N/m². An aluminum nail of radius 7.49x10 m…

A:

Q: (a) One end of a wire of length L and diameter d is attached to a high ceiling. The wire hangs…

A: Given that:E=14×106 Psi (lb/in2)d=0.15 inL=80 ft=960 inγ=0.215/in3

Q: The young's modulus of a material whose elastic strain and stress are 0.41 and 355.53 N/m?…

A:

Q: 200 stress 150 (MPa) 100 50 0-2 strain From the tensile stress-strain behavior for the brass…

A: SOlution: Given that A stress -strain curve and to determine the different srength

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).