03 (A)- Prove with aid of required figure and diagrams that the angular speed (w) of d.c. Shunt motor is V₁ Ba W= K, O -Te K, ²2 Assume the terminal voltage of the power supply feeding the armature is constant during the operation.

03 (A)- Prove with aid of required figure and diagrams that the angular speed (w) of d.c. Shunt motor is V₁ Ba W= K, O -Te K, ²2 Assume the terminal voltage of the power supply feeding the armature is constant during the operation.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: 3. A 4-pole, 250-V, d.c. shunt motor has a lap-connected armature with 960 conductors. The flux per…

A: Here DC shunt motor is given and we have to find developed torque and useful torque

Q: An eight-pole, 24 KW, 124 V, DC machine has a duplex LAP-wound armature which has 72 coils with 6…

A: No. Of poles, P = 8 No. Of parallel paths, A = 2*8 Conductors, Z = 72*6*2 Voltage, E = 124V Speed, N…

Q: A permanent-magnet DC motor has the following specifications: Motor Armature Supply Voltage…

A: In this question we have to find out motor armature current with given data.. In

Q: 250 V, 4 pole wave wound shunt motor has 650 conductors on its armature. It has armature and shunt…

Q: A 250 V dc shunt motor has an armature resistance of 0.2 Ω and a field resistance of 100 Ω. When the…

Q: A- A d.c. series motor draws 22 A from a 240 V line while running at 840 rpm. It has an armature…

Q: 2. The shown set of mechanical characteristics applies for: a) DC motor with armature voltage…

Q: A DC shunt motor produces an output power of 4.8 kW on the shaft with a speed of 1120 rpm and a…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A dc shunt motor runs at 900 rpm from a 400V supply when taking an armature current of 25A.…

A: Given: A dc shunt motor N1=900 rpmV1=400 VIa1=25 AV2=230 VIa2=15 ARa=0.8 Ωϕ2=0.75ϕ1

Q: A 230-volt series motor has an armature resistance of 0.32 ohm and a series-field resistance of 0.16…

A: Given: V=230 VRa=0.32 ΩN=500 rpmIa=32 A

Q: The torque in dc series motors depend on Select one: O a. the square of the field voltage Ob. the…

A: In this question we will write about torque in dc series motor...

Q: A DC generator has terminal voltage of 250 V and an induced voltage of 262 V when the generator is…

Q: An 4 pole, wave-wound DC motor has a 200 V supply. The armature has 1000 conductors and a…

A: An 4 pole, wave-wound DC motor has a 200 V supply. Armature conductor Z=1000 Armuatrur resistance…

Q: A 220 V shunt motor has armature and field resistances of 0.5 Q and 220 Q respectively. Initially,…

Q: M1. Which of the following is the preferred method of changing the direction of rotation of a DC…

A: a) The direction of rotation of motor is reversed either by changing the polarity of armature coil…

Q: An 8 pole DC shunt generator with 900 wave-connected armature conductors supplies 10ohm at 500 V…

A: To find the answers, we can use the following formulas and calculations:1.1 The flux per pole:The…

Q: If the voltage applied across the armature of a DC shunt motor is increased by 5% keeping its load…

A: generated emf in armature E = flux ×speed×no. of conductors60 ×no. of polesno. of parallel paths…

Q: Q 5. A wave-wound armature of a 6-pole generator has 51 slots. Each slot contains 20 conducto…

A: Emf induced in a dc machine is given by Eb=∅ NZ60×PA where ∅ is the flux per…

Q: A long shunt Motor ,The armature resistance is 0.1 ohm and the series field resistances are 0.0 ohm,…

A: The given data's are, Ra=0.1 Ω, B.d=1 V, P=4, p=11.19 kW, V=240 V, N=1000 rpm, Ia=50 A, Ish=1 A,…

Q: A 35.2 HP, 250 V, 100 A, 1800 RPM, series DC motor with no armature reaction is considered in this…

A: As per our policy, i am attempting first question. Given data, Ia=100 AIse=100 ARa=0.05 ΩRse=0.05…

Q: 3. A shunt generator is connected to a load that draws 30 KW on full-load. The armature resistance…

A: Given,Output power, Po=30 kWArmature resistance, Ra=0.1 ΩGenerated power, PG=33.50 kWShunt field…

Q: A separately excited dc motor operates at a rated terminal voltage of 240V. It has a total armature…

A: Given: Ia=35 A, Ra=0.22 Ω, kn=0.22, V=240 Volts. Required: Motor speed.

Q: Ashunt-wound DC motor with the feld coils and rotor connected in parallel (Figure 1) operates from a…

A: From the DC shunt motor equivalent circuit

Q: Q3) A 4 pole wave wound short shunt compound DC Generator supplies c current of 100 A to a load of…

Q: 1. A 4 pole, long-shunt lap wound generator supplies 20 kw at terminal voltage of 300 v. The…

A: This problem comes under electrical machine . It is related to dc generator . It is based on the…

Q: (a) Describe two main differences between a DC shunt-wound and separately-excited motor.

A: I am giving difference between shunt motor and separately excited motor.

Q: 2- A simple wave wound de shunt motor has the following data: Armature resistance =0.1 ohm Shunt…

A: Given data: Ra=0.1 Ω Rsh=100 Ω P=2 Z=400 Vs=400 V N=3000 rpm Is=104 A Wave winding, A = 2…

Q: a. The back-EMF generated by a DC motor is greatest when the motor is a) standing still b) running…

A: Back EMF of DC motor is directly proportional to the speed of the motor. Losses is occurs in field…

Q: As shown in the figure below, this is a speed regulation method for DC separately excited notor. 1)…

A: given figure is that a speed regulation method for DC separately excited motor: a) to explain about…

Q: 9. The synchronous speed of a three-Phase induction motor depends on the number of magnetic poles in…

Q: A shunt generator has field resistance of 602 when the generator delivers 60 kw he terminal voltage…

A: The solution is given below

Q: 23. When the circuit breaker is always tripping, most likely There is an overloading c. The supply…

A: In this question, We need to choose the correct options What is the circuit breaker is always…

Q: A 10 kW, 250 V shunt motor has an armature resistance of 0.5 Ω and a field resistance of 200 Ω. At…

A: Back emf of motor=terminal voltage- voltage drop in armature resistance . Back emf of dc motor is…

Q: 55 hp, 440 V, 400 rpm DC shunt motor draws 107 A when operating at rated conditions. The motor has…

A: In this question we will draw diagram of dc shunt motor showing all resistance,currents and…

Q: A 220 V shunt motor has an armature resistance of 0.4 ohm and field resistance of 140 ohm. The motor…

A: We have an shunt motor which is having, Voltage (V) = 220 V Armature resistance (Ra) = 0.4 Ω Field…

Q: Q5. B. A 4-pole 250-V, d.cl series motor has a wave-wound armature with 496 conductors. Calculate:…

A: This question belongs to electrical machine . It is based on d.c. series motor . This problem is…

Q: A 250 V shunt motor, having an armature resistance of 0.2 ohm draws from the mains a current of 50 A…

Q: Q) The input to 220 v motor is 12 kw a) the tor que developed the efficiency d-c shunt Colculate c)…

Q: A d.c. shunt motor after running for several hours on constant voltage mains at 400 V takes a field…

Q: The armature of a 10 pole DC shunt generator has 42 slots and is wave wound with 12 conductors per…

A: We need to Find armature current and generated voltage. Solution is attached below

Q: a) Draw the armature and excitation circuit of the motor and write the formulas for the equivalent…

A: a. For speed control DC shunt motor is preferred the formula for the equivalent circuit…

Q: A shunt DC motor is supplied by 520V terminals voltage and is used to supply a mechanical load with…

A: The solution can be achieved as follows.

Q: shunt-wound DC motor with the field coils and rotor connected in parallel (Figure 1) operates rom a…

A: Given Data:Supply voltage Vdc = 130 VField winding resistance Rf= 208 ΩArmature winding resistance…

Concept explainers

Stator and Rotor Magnetic Field

The stator and rotor magnetic field is the resulting magnetic field generated by a system of coils that are symmetrically aligned. They are supplied with polyphase currents. The magnetic field is generated by poly-phase (two or more phases) current or single-phase current. In the latter case, two field stator windings are supplied and two resulting electromagnetic fields are generated beyond the stage.

Question

03 (A)- Prove with aid of required figure and diagrams that the angular speed (w) of d.c.
Shunt motor is
V₁
Ba
W=
K, O
-Te
K, ²2
Assume the terminal voltage of the power supply feeding the armature is
constant during the operation.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 500 V shunt motor runs at its normal speed of 250 rpm with an armature current of 200 A. The resistance of armature is 0.12 02. Calculate the speed when a resistance is inserted in the field, reducing the flux to 80% of normal value, and the armature current is 100 A.
H.W 1) A 4-pole, 500 V d.c. shunt motor has 720 wave-connected conductors on its armature. The full-load armature current is 60 A and the flux per pole 0.03 Wb. The armature resistacne is 1.2 Q and the contact drop is 1 V per brush. Calculate the full-load speed of the motor. H.W 2) A d.c. series motor with series field, and armature resistance of 0.06 ohm and 0.04 ohm respectively is connected across 220 V mains. The armature takes 40 A, and its speed is 900 rpm. Determine its speed when the armature takes 75 A, and excitation is increased by 15% due to saturation.
Final 1A DC shunt motor is rated 10HP, 250V and is connected to 235V source. The armature resistance is 0.2 ohm, the field circuit resistance is 125 ohm and the total rotational losses are 380W. The motor is driving a load, and it draws an armature current of 30A, Calculate the output power. b) 41 d) 6490 6870 7492 7460 Boş birak
A shunt generator is connected to a load that draws 30 KW on full-load. The armature resistance is 0.1 ohm. If the power generated in the armature is 33.50 KW, and the shunt field resistance is 80 ohms, determine the: A. Variable copper loss B. Constant loss C. Maximum efficiency.
Example 2 The separately excited generator of example 1 is driven at revolving speed 1000 rpm and the field current is adjusted to 0.6 Amp. If the armature circuit resistance is 0.28 ohm, plot the output voltage as the load current is varied from 0 to 60 Amp. Neglect armature reaction effects. If the full-load current is 60 Amp, what is the voltage regulation? Solution
A 350 V shunt motor runs at it's normal speed of 720 r/min when the armature current is 90 A. The resistance of the armature is 0.3 ohm. Determine the following: (1) The kΦ1 of the motor. If armature current is 45 A and a resistance of 0.4 ohm is connected in series with the armature and the shunt field remaining constant determine the following: (2) The new kΦ2 of the motor. (3) The new speed of the motor in r/min If the current is 45 A and the shunt field is reduced to 75% of it's normal value by increasing resistance in the field circuit, determine the following: (4) The new kΦ2 of the motor. (5) The new speed of the motor in r/min
4. A shunt generator has a full load current of 196 A at 220 V. The stray losses are 900W and the shunt field coil resistance is 75N. If it has a full load efficiency of 90%, find the armature resistance.
at of estion An eight-pole, 24 KW, 124 V, DC machine has a duplex LAP-wound armature which has 72 coils with 6 turns per coil. Its rated speed is 3000 RPM. Assume no dead zone Find the constant K and the flux per pole to produce 80 Volts at no-load conditions Select one: O a None O b. K= 68.86 and flux = 3.33 mWb/pole Oc. K= 68.755 and flux = 3.7 mWb/pole O d. K= 95.5 and flux = 3.7 mWb/pole
A DC series motor having a resistance of 0.4 ꭥ and runs at 2000 rpm when connected to 250 V supply and drawing a current of 20 A. (i) What resistance must be added in order to limit the speed to 4000 rpm when armature current is 5A? Assume flux varies linearly. (ii) What resistance must be added to limit the speed to 1000 rpm when armature current is 30 A? Assume that the flux at 30 A is 20% more than that at 20A. (iii) At what speed the motor will run if it is connected directly to 250 V supply when the load is such that the current drawn is 30 A?
*need in 5 mins urgent please* A shunt motor connected to a 230-V supply has an armature resistance of 0.15 02, and a shunt field resistance of 230 Ohms. Calculate the value of back e.m.f. when the armature current is 100 A