A concrete dam retaining water is shown below, if the specific weight of concrete is 23.5 KN/m, find the factor of safety against sliding, the factor of safety against overturning, and the pressure intensity on the base. coefficient of friction between dam and foundation soil is 0.45 ? (y water 9.8 KN/m'). 03) A concrete dam retaining water is shown below, if the specific weight of concrete is 23.5 KN/m', find thefactor of safety against sliding, the factor of safety against overturning, and the pressure intensity on the base.coefficient of friction between dam and foundation soil is 0.45 ? (y water= 9.8 KN/m').-Am3m12m14m3m3m13m7m8m

Generally, the concrete dams are designed so that the weight of the dam is enough for sliding due to…

03) A concrete dam retaining water is shown below, if the specific weight of concrete is 23.5 KN/m', find the factor of safety against sliding, the factor of safety against overturning, and the pressure intensity on the base. coefficient of friction between dam and foundation soil is 0.45 ? (y water= 9.8 KN/m'). 3m 一 12m 14m 3m 3m 13m 7m 8m

03) A concrete dam retaining water is shown below, if the specific weight of concrete is 23.5 KN/m', find the factor of safety against sliding, the factor of safety against overturning, and the pressure intensity on the base. coefficient of friction between dam and foundation soil is 0.45 ? (y water= 9.8 KN/m'). 3m 一 12m 14m 3m 3m 13m 7m 8m

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.11P

See similar textbooks

Similar questions

1.) The specific weight of the concrete is 150 ??⁄??3, and the coefficient of friction between the base of the dam and the foundation is 0.42. If the factor of safety against overturning is 2, compute for the minimum width of the dam. CHOICES a.) 8.416 b.) 4.681 c.) 6.841 d.) 1. 684 2.) The specific weight of the concrete is 150 ??⁄??3, and the coefficient of friction between the base of the dam and the foundation is 0.42. Use 1.5 as the factor of safety (F.S) against sliding. Calculate the width of concrete dam that is necessary to prevent the dam from sliding. Unit of the Correct Answer: ft CHOICES a.) 5,783 b.) 7.358 c.) 3.578 d.) 8.357
Bleopage is assumed to occur beneath the concrete wall producing a finear distribution of hydrostatic pressure, as shown in Figure 1). Suppose that a-9 ft and b-12 ft. Figure 1 of 1 > Determine the location of the vertical resultant force due to seepage. Express your answer to three significant figures and include the appropriate units. 2p= Submit Part D UPM Value Submit Request Answer Determine the p-location of the horizontal resultant force due to pressure of water to the loft of the wall. Express your answer to three significant figures and include the appropriate units #A Value Units Request Answer Units
A pre-stressed concrete beam 100 mm wide and 300 mm deep is pre-stressed by straight wires carrying an initial force of 150 KN at an eccentricity of 50 mm. Determine the loss of pre-stress due to elastic deformation of concrete if the area of steel wires is 188 mm². Take EB and Ec as 210 KN/mm2 and 35 KN/mm²
A concrete dam is triangular in cross section and 30m high from the horizontal base. If water reaches adepth of 27 m on the vertical face, what is theminimum length of the base of the dam such thatthe resultant will intersect the base within themiddle third? What minimum coefficient of frictionis required to prevent sliding? Determine thepressure distribution along the base. Unit weight of concrete and masonry is 23.54 kN/m3 NOTE: CLEAR HANDWRITTEN SOLUTION
A vertical load Wis applied on a rigid plate supported on three vertical concrete pillars each 250 mm x 250 mm in cross-section. Initially the outer pillars are 1.75 m high while the middle pillar is 0.35 mm shorter. Find the safe load W, if the stress in concrete in outer pillar should not exceed 3.5 N/mm². Take E = 12500 N/mm². 1.75 m- WI 0.35 mm
5. A vertical, cylindrical tank, 5 ft in diameter and 12 ft high, is held together by means of two steel hoops, one at the top and one at the bottom. When molasses (sp gr 1.50) stands to a depth of 9 ft in the tank, what is the stress in each hoop?
3. The concrete column is reinforced using four steel reinforcing rods, each having a diameter of 25 mm. Determine the stress in the concrete and the steel if the column is subjected to an axial load of 1200 kN. Est = 200 GPa, 1200 kN Ec = 25 GPa. 300 mm 300 mm
250 30/0 Priv Ter * Question Completion Status: 87°F Cloudy L 4 PA 5 6 Cross Section Area, A = 0.04 m² Axial Load, P = 171 KN Angle, 0 = 53° 7 # The bar is subjected to the axial load. There is a shaded section which is oriented at 0 from the horizontal. Given: 8 10 Moving to another question will save this response. LA A Determine the average normal stress (MPa) acting over the shaded section. Express your answer in 2 decimal places. $ 12 13 14 15 16 % P > S (C 17 & 18 19 hp W 00 20 6
A rectangular concrete beam has a width of 400 mm and an effective depth of 700 mm. It is reinforced with five 28-mm diameter bars for tension only. Concrete strength is f's = 21 MPa and steel yield strength is fy = 275 MPa. Which of the following most nearly gives the depth of the rectangular compression stress block? A. 188.15 mm B. 151.93 mm C. 139.51 mm D. 118.58 mm
SITUATION II: A reinforced concrete beam with a cross-section of 250mm x 460mm (60 mm steel cover). Use the following properties to calculate what is required: f'c = 20.7 MPa fy = 344.7 MPa A, = 3 – 36mm A', = 2 – 25mm 8) Draw the stress diagram of the beam section 9) Calculate for the depth of the compression block. 10) Calculate for the compressive strength of the concrete (in KN). 11) Calculate for the nominal moment capacity of the beam.
Calculate the total stress in the given beam due to prestress only. A rectangular beam 200 x 300 mm is prestressed with 15-6 mm diameter wires located at 65 mm from the beam soffit and 2-6 mm diameter wires located 25 mm from the top of the beam. The prestress is 1000 MPa with a length of 8 meters.
Please give proper solution other wise skip I want to learn. A Masonry dam 8 m high, 1.5 m wide at top and 5 m wide at the base retains water to a depth of 7.2 m, the water face of the dam being vertical. Find maximum and minimum stress intensities at the base. The weight of water is 9.81 kN/m³ and weight of masonry is 22 kN/m².