0.8 m 0.4 m В 0.6 m 1.6 m P = 1.2 kN 2 m The rigid beam AB is hinged to a support at A and supported by two vertical wires attached at points C and D. Both wires have a diameter of 2.5 mm and are made of steel with Est = 200 GPa. Determine the tensile stresses oc and Op in the wires due to the load P = 1.2 kN and find the downward displacement OB at end B of the beam. %3D

Q: List five things that could cause premature bearing failure

A: No matter what, things are bound to break. The same holds for bearing. But it can be prevented by…

Q: What is the main cause of bearing failures?

A:

Q: Maximum Equivalent Stress (Safety Factor) ansys

A: Here is the solution of your question:-Explanation:In ANSYS, the maximum equivalent stress and…

Q: For the following smooth channel roller support. Which of the following statements are true?   a.…

A: For the given system since all the surfaces are smooth thereby no friction will act on the surfaces…

Q: Define the term critical load?

A: Critical load – critical load on a column is the maximum value of load which can be carried out by…

Q: What are the Load factors and what do they include?

A: Load factor: In general, the load factor is defined as the ratio of all the forces (weight of…

Q: Why is the 8 kN load not considered here?

A: This question is based on the concept of normal stress.

Q: Describe how torque on a solid shaft can be measured using strain gauges?

A: Strain guage converts the torque into change of electrical resistance. This guage is bonded to…

Q: = It is required to design a split muff coupling to transmit 60 kW power at 140 rpm. The shafts, key…

A: Step 1:Calculating Shaft Diameter :The power transmitted by the shaft can be related to the torque…

Q: Truss members can change their length due to a change in temperature. True or false?

A: In truss members, there is no change in length. But due to changes in temperature stress is build up…

Q: Due to imperfections in manufacturing or specific applicationof the load, a column will never…

A: Under the application of axial load over a column when there is a deflection in the lateral…

Q: The bolts used to mount an engine on an industrial machine must each carry a static tensile load of…

A: For the bolt material, SAE grade 5 UNC, the yield strength is generally,

Q: Two identical aluminum plates are each 3 in thick, and are com Washers are used under the head of…

A: Given that, Thickness of plate, t= 3 in,Washer properties:ID=0.531 in,OD=1.062 in,thickness=0.095…

Q: What happens if the load on an actual column exceeds its critical loading?

A: There are two types of the column, 1. Short Column 2. Long Column The slenderness ratio and length…

Q: Q1- Find the power required to drive a 1.5-in power screw having double square threads with a pitch…

A:

Q: Industrial Maint. What are the three types of loads that may be placed on a bearing?

A: The three types of loads that may be placed on a bearing are

Q: What is the maximum deflection?

A: Given Beam To find Definition of maximum deflection

Q: What are Statically Intermediate Axially Loaded Members?

A: When the static equilibrium equation does not alone solve the load or stress calculations, then such…

Q: Connecting rod bearings are to be replaced. The journal measures 70.866 mm (2.790 in.)​. The…

A: The Size bearings for above requirements are U/S--0.381 mm (0.015 in) undersize.

Q: What is the cause of slipping inductile failure?

A: Causes of slipping in ductile failure are as follows

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.