0.75 in.- (b)

Q: A 226-N object is hung from the end of a wire of cross-sectional area 0.03 cm-. The wire stretches…

A: Given: Force,F=226NArea,A=0.03cm2=0.03×10-4m2Length,L=150cm=150×10-2mChange in…

Q: Two strips of metal are pinned together as shown with a rod 10 mm diameter. The ultimate shear…

A: Given: Diameter=10mm Therefore, =5mm Shear stress=60Mpa.

Q: Asolid copper cube has an edge length of 85.0 cm. How much stress must be applied to the cube to…

A: Here in this Question The Edge length of the copper cube is given to be 85.0 cm and it has been…

Q: A wire with circular base of radius 3 mm was subjected to tensile stress of 13.5 Pa. If half the…

A: Given that- R=3 mm Now stress=F/A

Q: One end of a vertical metallic wire of length 2.0 m and diameter 1.0 mm is attached to a ceiling,…

A: Answer:   To determine Young’s modulus of any metal is given as below:     The slope of the above…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange Band loaded, as shown. The…

A: ANSWER :- As in question normal stress is asked and can be calculated as force/area. Area of rod 1…

Q: Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P…

A: Consider the given data as below. Diameter of wire CD, dw=18 inch Diameter of the pin at B, dp=18…

Q: The cross-section of a hollow shaft subjected to a torque T is shown in the figure. Which point…

A: The answer to the above problem is given below

Q: The screwgate carabiner is left open as it is loaded by a rope as shown. Calculate the stress state…

A: Stress is defined as force per unit area.  σ=FA Where F is a force and A is cross-section area.

Q: A steel rod 2.0 m long has a cross-sectional area of 0.30 cm2. It is hung by one end from a support,…

A: Given information: The length of the rod, l=2.0 m The cross-sectional area of the rod, A=0.30…

Q: The beam is supported by a pin at A and a short link BC. Figure 0.5m 1 m 4P 1.5 m 4P 1.5 m 0.5m 1 of…

A:

Q: A stepped bar shown is subjected to an axially applied compressive load of 35KN. Find the Maximum…

A: Solution:-Given thatAxially applied compressive load (P)=35 kN=35×103 NDiameter of upper plate (d)=2…

Q: Two equal and opposite forces F and -F act on a rod of uniform cross-sectional area A, as shown in…

A: As the net force acting on the rod is zero, it is in equilibrium. Let the tension in the segment AB…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown in the…

A: Given diameter of Rod(1) d=1.75in Rod(2) D=2.50 For the given configuration rod (1)  pushes rod (2)…

Q: The five-bolt connection must support an applied load of P-4700 lb. If the average shear stress in…

A: Given that - Five bolt connection Applied load(p)= 4700lb Averge shear stress in the bolt must be…

Q: Determine the tensile stress in each cable given that all the cables have a cross-sectional area of…

A:

Q: A sculpture weighing 10,000 N rests on a horizontal surface at the top of a 6.0-m-tal vertical…

A: The stress of a material can be described as the amount of ultimate stress that can a material…

Q: Determine the minimum height h of the beam with a base of 8 inches if the flexural stress is not to…

A: Torque or moment of a force is given by the formula M→=r→×F→ = rperpendicular ×F Where F is the…

Q: The five-bolt connection must support an applied load of P = 3400 lb. If the average shear stress in…

A:

Q: The five-bolt connection must support an applied load of P-4900 lb. If the average shear stress in…

A:

Q: The rigid beam AB is subjected to a varied force10kN and is supported by a steel rod of 17 mm…

A:

Q: The hollow steel cylinder DNGL, fixed on one end, is subjected to two torques and an axial load, as…

A: Area of the hollow cylinder is find by the A=πRO2-RI2

Q: A steel wire having a radius of 2.0 mm, carrying a load of 4 kg, is hanging from a ceiling. Given…

A:

Q: A hollow member having the cross section shown is formed from steel alloy sheet of 2mm thickness.…

A: Given data The thickness of the sheet is t = 2 mm The shearing stress is τs = 3 MPa The shear…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s=…

A: The slope of the stress-strain graph gives the Young's modulus of the material.

Q: The wood beam is subjected to a load of 12 kN. If grains of wood in the beam at point A make an…

A: