4.14. Often, in chemical processing plants, there will be more than one type of instru-mentation measuring the same variable at the same instance during the process.Owing to the nature of measurements, they are almost never exact, and hence canbe represented as a fuzzy set. Owing to the differences in instrumentation, the mea-surements will usually not be the same. Take, for example, two types of temperaturesensors, namely, a thermocouple (TC) and a resistance temperature detector (RTD)measuring the same stream temperature. The membership function of the two typesof temperature sensors may look as in Figure P4.14.RDTTCu = 1.0 -H = 1.00.5 -0.5 -77787980T (°C)7879808182 T(°C)FIGURE P4.14When an operator who prefers one measuring device ends his or her shift, and thenis replaced by another operator with a different preference in measuring device,there may be a problem in determining the actual value of a variable. To avoidthis problem, it was decided to plot the membership functions of the two types ofsensors, take their union, and employ defuzzification to select one temperature forthe operator to use. To find this temperature, for each of the seven methods presentedin this chapter, assess (a) whether each is applicable and, if so, (b) calculate thedefuzzified value, z".

RTD and Thermocouple are well known temperature sensors which are used to sense and measure the…

0.5 0.5 - 77 78 79 80 T(CC) 78 79 80 81 82 T(°C) FIGURE P4.14 When an operator who prefers one measuring device ends his or her shift, and then is replaced by another operator with a different preference in measuring device, there may be a problem in determining the actual value of a variable. To avoid this problem, it was decided to plot the membership functions of the two types of sensors, take their union, and employ defuzzification to select one temperature for the operator to use. To find this temperature, for each of the seven methods presented in this chapter, assess (a) whether each is applicable and, if so, (b) calculate the defuzzified value, z*.

0.5 0.5 - 77 78 79 80 T(CC) 78 79 80 81 82 T(°C) FIGURE P4.14 When an operator who prefers one measuring device ends his or her shift, and then is replaced by another operator with a different preference in measuring device, there may be a problem in determining the actual value of a variable. To avoid this problem, it was decided to plot the membership functions of the two types of sensors, take their union, and employ defuzzification to select one temperature for the operator to use. To find this temperature, for each of the seven methods presented in this chapter, assess (a) whether each is applicable and, if so, (b) calculate the defuzzified value, z*.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

*Use 4 decimal places. For the circuit below, determine the diode voltages VD1 and VD2, diode currents Ip1 and Ip2, and voltage across the resistor, VRLIMIT- Assume r'a (for both diodes)=200. Note D, is Germanium, D2 is Silicon, VBJAS = 22V and RLIMIT = 2 kohms. VD1 = 0 V; VD2 = 0 V; Ip1 = Blank 3 mA; Ip2 = Blank 4 mA ; VRLIMIT = Blank 5 v Use ideal model. Capture3.JPG +VD1- +VRLIMIT +Vp2- Ip2 VBIAS 두
Using 2nd approximation for the circuit shown, assuming that the diode used is a silicon diode, determine the currents ID1, ID2 and current through R2. Finalize answers as follows: ID1= Ir2= ID2= R2 D1 3.3 kQ BAT1 D2 20 V R1 5.6 kn
B01.2 QUESTIONS ON THIS CHAPTER C a رها The conductivity of a pure semiconductor is due to: al electrons. 2 □ 3 04 □5 al 02 3 04 5 A pure semiconductor is a good conductor when the temperature is: □ 2 □3 4 5 AP type semiconductor is obtained by adding impurities such as: al LESSON BOI: INTRODUCTION TO SEMICONDUCTORS 2 holes positive ions of the N regions and electrons electrons and holes positive ions of the P regions and holes □ 3 04 5 very high very low ol □ 2 □ 3 4 □5 absolute zero when ranging between 0 and 25 °K it is not affected by temperature An N type semiconductor is obtained by adding impurities such as: those belonging to group III of the periodic table of the elements al phosphorus only those belonging to group V of the periodic table of the elements those belonging to the group III of the periodic table of the elements antimony only gallium only boron in the proportion of 25 %, and arsenic as 75 % boron only aluminum and antimony together at 50% those belonging to group V…
For number 12 question Final problem, you will need a test charge to move from one point to another point. Please consider the value of the test charge 15 mC 12. Determine the work needed to move a 13.3 mC charge from 1.2 mm to 0.41 cm.
A Si pn junction photodetector has a depletion region of 3 um, a cross sectional area of 3x10 cm, and a minority carrier lifetime of 1 us. Photons of $80 nm and optical power of 24.7 mW are incident on the detector, the detector absorption coefficient at the incident photon wavelength is 0. 7×10 cm. At 300 K temperature the detector photo-current will be? O a. 366.9 A Ob.111.2 pA Oc 210.6 uA Od. 2149 A
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
#4(a) An 8.2 V (8.2 V at 25 °C) has a positive temperature coefficient of 5.4 mV/°C. What is the output voltage if the temperature rises to 90° C? Page | 4 b) Name two applications of the Zener Diode
* Find the current through the diode in the circuit shown. Assume the diode to be ideal. 50 92 A R₁ V= 10 V 185 mA O 46 mA 140 mA 28 mA wwww 5923 R₂ B D
Replace the diode, D1, with the constant voltage model. V1=3.5 V, R1 = 2kΩ , R2 = 3kΩ , R3 = 3kΩ , VON = 0.7 V i) Find the value for V2 by applying the constant voltage model to D1 ii) Find ID, IR1, IR2, IR3
110 Vrms 60 HZ (c) priy 1/5 •ooooo reelle Vp(sec) D3 D₂ 0₁ B D₁ 47 µF" Output All diodes are 1N4001. Figure 1.1 Unregulated Power Supply R₁ • 2.2 ΚΩ Experiment Design using the breadboard Figure 1.1 and measure the ripple (Texp)
For uncontrolled half wave rectifier, R=80ohm, L=0.15H, f=50Hz and Vm=311V. Find the point when the current reaches to zero in radian. In your calculations, take 3 digits after the comma and take pi = 3,14; Enter your answer into the system in terms of the desired unit only as a number.
Find the Vout of the Circuit below during the Positive half cycle. Consider the Diodes as a Silicon Zener Diode. V2 D1 V3 D2 2 2 2 V1 AC Vout R1 12 1k