0.10 m/s 6 m/s FRx

Q: Given: Q h BE Suction pipe Discharge pipe 1.80 m pump Datum line DA = 20 cm = 0.20 m DB = Dc = 15 cm…

A:

Q: A fluid moves in a steady flow manner between two sections in a flow line. At the entrance section…

A:

Q: diameter pipe with a density of 0.0035 slugs/ft³ and a uniform speed of 696 ft/s. (a) Determine the…

A:

Q: Air at standard conditions enters the compressor shown in the figure below at a rate of 10 ft³/s. It…

A: Given: Air standard conditions of compressor Volume flow rate, Vf = 10 ft3/s Leaving pipe diamter,…

Q: 2) Consider the system of cylindrical pipes shown in the following figure, where a flow of water is…

A: Given: The diameter of pipe 1, D1 = 15 cm The diameter of pipe 2, D2 = 5 cm The pressure in pipe 1,…

Q: Three pipes steadily deliver water at 20°C to a large exit pipe as shown in the figure given below.…

A: given datadiameter of pipe D1=4 cm=0.04 mD2=5cm =0.05 mD3= 6cm =0.06mvelocity v2 =5 m/sthe exit flow…

Q: For the flow of water (p=1000 kg/m³) through the control volume shown in Figure below, use R.T.T. in…

A:

Q: 1. Water (p = 1000- kg H = 10-3 flows in a horizontal constant-area pipe; the pipe cross ms section…

A:

Q: Water with density 1000 kg/s enters a lawn sprinkler which is rotating at 500 RPM through its base…

A:

Q: 3. A square duct of air (p = 1.2 kg/m³; µ = 1.9x104 kg/m-s) is fed from a pressurized tank as shown…

A:

Q: jet

A: α=30oV1=30 m/su=12m/sϕ=18o

Q: A tank with openings 1, 2, and 3 is moving to left at a speed of 25 km/h. Knowing that D1 = D2 = 20…

A: Consider the diagram shown below with the velocities of flow. The velocity of the tank is The…

Q: A pump is to deliver water at a head of 40 m, the water temperature being 38oC and barometric…

A:

Q: the pipe is 2 feet lower than at point A. Draw a clear diagram of the pipe system that indicates the…

A: Solution is attached below

Q: projectile-like object with maximum diameter of 20 cm is placed at the exit of a 25-cm-diameter…

A:

Q: The water enters the blades of the Francis turbine at an angle of 30 and leaves in radial direction.…

A: The inward flow reaction turbine having radial discharge at outlets is known as Francis turbine,…

Q: A fire robot is designed as shown in Figure 2 to fight the fire while it moves with 0.38 m/s…

A: Given: The velocity of fire arm robot, V = 0.38 m/s The inclination of pipe, θ = 45 degree The mass…

Q: The Figure shows the arrangement of a circuit for a hydraulic system. The pump draws oil with a…

A: Disclaimer: “Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: The force that drives the flow of fluids is the pressure difference; a pump works by raising the…

A: Power consumed = 3.8 kW Pressure difference = 7 kPa

Q: A 90" elbow is used to direct water flow at a rate of 0,025 m3/s in a horizontal pipe upward. The…

A:

Q: A large lawn sprinkler with four identical arms is to be converted into a turbine to generate…

A: Given data: The mass flow rate of water in the sprinklers is m = 12 kg/s. The velocity of water…

Q: A hydraulic nozzle is fed from a 0.19 m diameter pipe with an inlet pressure of 581 kPa and a…

A:

Q: through a U-section pipe as shown in Figure 1.2. At flange (1) the total absolute pressure is 240…

A:

Q: Q5. Two tanks A and B of surface areas 600 m2 and 300 m2 are connected by an orifice of 0.18 m2 in…

A:

Q: left ventricle into the aorta can be modeled as a reducing nozzle (Figur below). Model both the left…

A: Given data as per questionFor Left ventricle, Loaction 1d1=3.1 cm=0.031 mv1=120 cm/s=1.2 m/sP1=130…

Q: A reversing elbow used to deflect water flow at a rate of 14 kg/s in a horizontal pipe to make a…

A:

Q: As shown in the figure, water enters and leaves a U-shaped piece of pipe in the horizontal plane.…

A: Density It is the property of fluid which is ratio of mass and volume of fluid.   Continuity…

Q: The impeller of a centrifugal pump has inner and outer diameters of 15 and 35 cm, respectively, and…

A: Given di=15 cm=0.15 m do=35 cm=0.35 m Flow rate=V˙=0.15 m3/sSpeed=N=1400rpmBlade width at inlet=wi=8…

Q: In a Francis turbine, the pressure gage in the turbine casing reads 394 kpa. The elevation above…

A:

Q: A three-arm sprinkler is used to water a garden by rotating in a horizontal plane. Water enters the…

A:

Q: Water leaves a hose at a rate of 3.6-kg per 2.0-s with a speed of 19.3-m/s and is aimed at a toy car…

A:

Q: A reducing bend with an inlet diameter of 200 mm and exit diameter of 150 mm bends 40 degrees…

A:

Q: ine a fluid packet moving through the Orifice plate. What happens when it’s Kinetic Energy as it…

A:

Q: 1. A fluid is flowing in a 6in diameter pipe at a pressure of 4PSI with a velocity of 8ft/s. The…

A:

Q: A cylindrical tank is being filled with water flowing with constant velocity V1 through a tap (Tap…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: A- Blood flow from the left ventricle into the aorta can be modeled as a reducing nozzle (Figure…

A: Given Inlet diameter =  3.1 cm Outlet diameter = 2.7 cm Inlet pressure = 130 mm Hg Outlet pressure…

Q: Water is flowing through a U-section pipe as shown in Figure 1.2. At flange (1) the total absolute…

A:

Q: Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 150 L/s, and leaves the…

A: Given Data: The flow rate of water is, Q=150 L/s=150 L/s×10-3 m3L=0.15 m3/s. The diameter of the…

Q: A 12-in diameter pump rotating at 600 rpm develops a head of 500 ft. Determine the peripheral…

A: