3.3 The torque of 100 kip - ft produces a maximum shear stress of 8000 psi in the16-ft-long hollow steel shaft. Note that the inner diameter of the shaft is two-thirds ofits outer diameter D. (a) Determine the outer diameter D. (b) Find the angle of twistof the shaft. Use G = 12 x 106 psi for steel.

Answered: Image /qna-images/answer/d3193511-fe73-4d9d-9237-4370cf12f3c2.jpg

.3 The torque of 100 kip - ft produces a maximum shear stress of 8000 psi in 6-ft-long hollow steel shaft. Note that the inner diameter of the shaft is two-thirds s outer diameter D. (a) Determine the outer diameter D. (b) Find the angle of tw f the shaft. Use G= 12 x 106 psi for steel.

.3 The torque of 100 kip - ft produces a maximum shear stress of 8000 psi in 6-ft-long hollow steel shaft. Note that the inner diameter of the shaft is two-thirds s outer diameter D. (a) Determine the outer diameter D. (b) Find the angle of tw f the shaft. Use G= 12 x 106 psi for steel.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve fast I will upvote
a)jj holiow steel tube jsed in a roof structure has an outer diameter, d; = 104 mm and inner diameter, dz = 82 mm. The length of the tube is given by L = 2.75 m and has shear modulus, G = 28 GPa. If the tube is twisted in pure torsion by torques acting at the ends, distinguish the angle of twist when the maximum shear stress, Tmax = 48 MPa.
SECTION: 500mm 20 KN I5 KNIM 1000 mm 12 m Ps 800 KN e : 400 mm (ASSUME IS % LOS SES) A. Determine the stress at the bottom in the free end. (MPa) B. Determine the stress at the top in the fixed end. (MPa)
3. Two-solid 2.0-in.-diameter steel shafts are connected by the gears shown. The shaft length are L, = 12 ft and L2 = 20 ft. Assume that the shear modulus for both shafts is G = 12,000 ksi and that the bearings shown allows rotation of the shafts. If the gear at D is rotated at an angle of 8°, what is the maximum shear stress in each shaft. L2 Rg = 5 in. (1) B Tp (2) Rc = 3 in. D
A solid circular bronze [G = 6,500 ksi] shaft, 6.2 ft long and 1.150 in. in diameter, carries a torque of 85 lb-ft. For this shaft, determine: (a) the maximum shear stress in the shaft. (b) the magnitude of the angle of twist. Answer: (a) Tmax psi (b) Ф%3
Problem 1: Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T=2880 N and T;=432 N. The maximum bending moment is atx= 230 mm (point B), and it equals M= 698.3 N•m completely reversed, where the torque is constant at 612 N.m at the same point. The shaft material is AISI 1020 CD steel. Take the stress concentration conditions at B to be Shoulder fillet-sharp, with notch radius r=0.6 mm (Table 7-1). y 230 mm T, 280 mm 30-mm dia. T C 300 mm 250-mm dia. 400-mm dia. 270 N 1800 N a) Sketch a general shaft layout in 2D (x – y axes), including all components and torques, then calculate all reactions. b) Based on the current shaft dimensions and using only forces at B and C, find the lowest critical speed of the shaft. c) Discard the indicated shaft diameter and use DE-Goodman criteria to determine the critical diameter of the shaft based on infinite fatigue life with a design factor n of 1.5. (Take the same value of endurance limit as that used in…
Solve it correctly please. I will rate accordingly.
A solid circular bronze [G = 6,500 ksi] shaft, 6.0 ft long and 1.325 in. in diameter, carries a torque of 90 Ib-ft. For this shaft, determine: (a) the maximum shear stress in the shaft. (b) the magnitude of the angle of twist. Answer: (a) Tmax = psi (b) Ф%3D
A compound shaft made of steel and aluminium transmits 75 kW at 900 rpm. Determine the maximum shear stress and relative angle of twist between surfaces at two extreme ends located at A and C. Neglect any strain concentration effect. Esteel = 207 GPa, EA1 = 73 GPa, VAI = 0.334, and Vsteel = 0.33. F Aluminium 60 800- B Steel 75 1000 All dimensions are in mm
The shown L-shape cantilver is loaded as shown and fixed at A. It has a constant section of 40 mm X 20 mm. For point I located at 50 mm from support A, at the midheight of the section, determine the principal stresses, the principal planes and the maximum shear stress. y 50 mm 150 mm 40 mm 0.5 kN H- I 20 mm 3 kN 160 mm 2.5 kN
The shaft AB is formed by bonding steel tube and a brass core. Outer diameter of the steel tube is 60 mm and the diameter of the brass core is 30 mm. The shaft is subjected to uniform distributed torque o t kNm/m. The allowable shear stresses for steel and brass are (Tsteel)all = 80 MPa and (Tbrass)all = 50 MPa, respectively. Determine a) the maximum value of the uniform torque t , b) the corresponding angle of twist at A. (The shear modulus for steel and brass are Gsteel = 77 GPa and Gbrass = 40 GPa, respectively) - Steel Tube A t kNm/m B 30 mm 15 mm 1 m 1 m Brass Core Cross Section