..A 3-phase,8 pole 50 Hz, star connected salient pole synchronous generator has 90 slots with 4 conductors per slot connected in series in each phase. The coil pitch is 10 slots. If the maximum value of the airgap flux is 45 mWb and the flux-density distribution in the airgap is sinusoidal. Determine a. the rms phase voltage b. the rms line voltage c. If each phase can carry 650A in current, what is the KVA rating of the machine?

..A 3-phase,8 pole 50 Hz, star connected salient pole synchronous generator has 90 slots with 4 conductors per slot connected in series in each phase. The coil pitch is 10 slots. If the maximum value of the airgap flux is 45 mWb and the flux-density distribution in the airgap is sinusoidal. Determine a. the rms phase voltage b. the rms line voltage c. If each phase can carry 650A in current, what is the KVA rating of the machine?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. The portion of the flux that goes through one of the transformer coils but not the other one is called. A) Average flux B) Mutual flux D) Leakage flux C) Total flux 5. The fundamental component of the magnetization current ------- the voltage applied to the core by ------ 90°: A) Lags, 45° B) Leads, 45°. D). Leads, 90°. C) Lags, 90°. 6. The ----- are resistive heating losses in the core of the transformer. A) Hysteresis losses. B) Copper losses. C) Leakage flux losses. D) Eddy current losses. 7. The total rotational losses of an induction motor are a combination of: A) Friction losses B) Windage losses. C) Core losses. D) Stray losses. 8. Induction motors are now the preferred A) absence of brushes. choice for industrial motors due to B) Small size. C) Less control requirements. D) rugged construction. 9. For an induction motor, if the synchronous speed is 1800 r/m, and the rotor speed 180rad/sec, then the slip will be: A) 5.5 % C) 6% B) 4.5% D) 4% 10. The lower the speed of an…
for a 20kW PM synchroneous generator that produces 400V and 50A at its output. the resistance of the coil is 217.412 micro ohms. area of the magnetic feild is is 0.146 squared meter. it has a magnetic flux density of 1.49T, a frequency of 50Hz. Calculate the iron losses of this generator with no load. show all working Please answer in short like it definitely don't reject in shorts please... ..
A synchronous generator runs at 250 rpm and generates at 50-Hz. There are 216slots, each containing 5 conductors arranged in a full-pitched winding for 3-phasestar connection. All the conductors of each phase are in series and the flux perpole at no-load sinusoidally distributed over the pole pitch is 30 mWb. Find the emfinduced in each phase winding and the terminal voltage.
A 2 pole wave wound dc generator has 44 slots, each slot having 20 conductors. The flux/pole is 0.018 weber. At what speed the armature be rotated to get an induced emf of 220 V. What will be the induced emf developed if the armature winding is lap connected and runs at the same speed. Speed Generated Emf when lap connected
9.09 The flux density distribution in the air-gap of a certain generator is such that it contains a fundamental, a third harmonic, and a fifth harmonic. The flux per pole due to the fundamental distribution is 9 x 10-3 weber, that due to the third harmonic distribution is 0.9 x 10-3 weber, that due to the fifth harmonic distribution is 0.4 x 103 weber. There are four armature slots per phase per pole, the connection are made for three-phase wye. and the coil pitch is 12/15. The frequency is 60 cycles and the generator has 4 poles. (a) Calculate the emf/turn. (b) If there are six turns/coil and two coil sides/slot, calculate the emf per phase. (c) Calculate the emf between line terminals. Ans. 2.32V; 212V; 364V
A 3-phase, 50 Hz, 16 pole generator with concentrated windings has 144 slots with 10 conductors per slot. The flux/pole of 24.8 mWb is sinusoidally distributed. The coil is full pitched. Find the line emf.
A 9.9 kV, Y-connected, 3 phase alternator has a synchronous reactance of 8 ohms per phase and negligible resistance. At a certain field current the armature is known to induce 8.2 kV per phase. Calculate the power that can be developed by the alternator at this excitation.
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
The armature of a two-pole generator is rotating at 3600 r/min. The armature has a simplex lap winding with a total of 1504 conductors. Determine the generated voltage when the flux per pole is 600,000 x 10-8 Wb. 5.5
There are 175 slots in a 3-phase, 16-pole, 50 Hz., star connected alternator. There are 4 conductors in each slot and all the conductors in a phase are connected in series. Coil span is 130° electrical and the flux per pole is 0.04 Weber sinusoidallly distributed. Calculate the emf induced per phase.
Draw a complete circuit diagram of 1 phase synchronous alternator including the field excitation circuit. Then, draw the phasor diagram of the generator a general leading power factor. Include the phase resistance in the diagram.
D2. When a generator's full-load output voltage is the same as its no-load output voltage it is said to be a) under-compounded b) flat-compounded c) over-compounded d) none of the above D3. The output of an overcompounded DC generator can be lowered by use of a a) rheostat connected in series with the series field b) rheostat connected in parallel with the series field c) rheostat connected in parallel with the shunt field d) none of the above D4. When might it be desirable to use an overcompounded generator? a) never b) always c) to compensate for line loss d) when you need a higher no-load voltage than your full-load voltage