... 200 lb/ft 1200 lb-ft A B 30- ft 0.800 kip the cantilever beam shown on the above figure, determine the following: 1. Shear force at B- Blank 1 Ibs 2. Shear force as function of x - Blank 2 Ib 3. Bending moment as function of x Blank 3 Ib.ft

Q: For a beam having the cross section shown, deter- mine the largest allowable vertical shear if the…

A: At centroid ; Q = 2 ×10×40×40 +20×50×10= 42,000 mm3 = 4.2×10-5 m3 t = 50 mm  So, Q/T = 840 mm2

Q: A force and a moment are applied to the member shown. Determine an equivalent force and moment…

A:

Q: What is the shear between A and B, at a distance of 4m from point A.

A: Given data in question  UDL = 29 kN/m Span member length = 11 m Point load = 21 kN Concentrated…

Q: Pa3kips wEl00 PLF 201 to BEAM 24

A: Given beam.

Q: 24 kN -3 m 3 m 3 kN/m m

A: Frames are generally used in the section where the transferred load distribution is provided like in…

Q: Show the Shear and Bending Diagrams. And write legibly

A: Shear force and bending moment diagram

Q: he beam in the figure below is perpendicular to the wall and supported at the wall by a hinge at…

A:

Q: 6 kNI SkN/m -1.5m- 15m

A:

Q: What is the shear at C to the nearest 0.01k? Be sure to use the correct sign. P 86.3 k P –6 ft- D 2…

A: Given, P=86.3 K

Q: The pin at C is supported in a double shear connection. If the allowable shear stress is 70 MPa,…

A: step 1-

Q: 5 kips A 10 kips 8'-0" B 16'-0"

A:

Q: The internal normal force in kN at point C is mostly near

A:

Q: 30 kN/m 100 kN 20 kN/m Hinge, -Hinge -10 m- 10 m 10 m- 2 m –- Figure 3 Figure 4

A:

Q: 60 mm 60 min 60 mm w 200 mm 6.3 Three boards are nailed together to form a beam shown, which is…

A: s = 75 mm  Fnail = 400 N  w = 120 mm

Q: What is the number on the last part of the bending moment where it says 30 x ....

A: Given data:

Q: Determine the axial forces, shears, and bending moments at points A and Bof the structure shown. 100…

A: Finding out axial force,shear force and bending moment at A and B .

Q: II- Stress Analysis of Trusses 2. Calculate the internal force in members EJ and LC. 2,400. Ibs…

A:

Q: •3. Draw the shear and moment diaoram, and determine the max shear and maximum moment. 30 kN/m OD 3m…

A: A loaded simply supported  beam is given in the question and it has been asked to determine and draw…

Q: 01: Determine the forces and state if its tension or compression in members AB, AH, BH, BG, BC and…

A: Find the forces in members AB,AH,BH,BG,BC and HG -

Q: 15 ft 40 k 15 ft- 3 klf 15 ft- H

A:

Q: For the truss shown: a) calculate support reactions. b) To use the method of joints, which joint(s)…

A:

Q: B A shear diagram, bending moment diagram maximum shear force and bending moment?

A: Calculation of support reactions

Q: Draw Shear & Moment Diagrams A * 3' 3' 9k 6' B 3' 3k

A:

Q: 1/ By section method draw axial force, shear force and bending moment diagram A 5 kN 3 1 M 4 B 2…

A:

Q: 19.1 A 60-ft-span of a simply supported pretensioned beam has the section shown in Fig. 19.12. The…

A: segment  A(in2) y(in) Ay Iy(in4) d(in) Ad2+Iy(in4) 1 120 3 360 360 16.936 34779.37 2 144 18 2592…

Q: BDM? bending moment diagram

A: In continuation of previous question, only bending moment diagram is provided.

Q: A 3 13 S C Find all force and moment reactions method including force at of consistent deformations…

A:

Q: Draw shear force and Bending moment Diagram 8 kip 3 kip/ft A B 3 ft 5 ft 8 ft

A:

Q: Analayze given truss and find member forces.

A:

Q: The internal normal force in kN at point D is mostly near

A: Let FBC be the force in BC.

Q: Q-for the beam calculate the max bending and shearing stresses 5kN/m +2m+ 10m + 400mm +

A: Step 1: Step 2: Step 3: Step 4:

Q: What is the Vertical Reaction at A in kips? [add negative (-) sign if answer is t

A: Solution: The Vertical reaction in A.

Q: B\ 3PM

A: a symmetrical overhanging beam is given we have to make shear force diagram(SFD) and bending moment…

Q: A sign is subjected to a wind loading that exerts horizontal forces of 1.5 kNon joints B and C of…

A: Truss : A truss is a construction made up of elements arranged in connected triangles such that the…

Q: What is the internal bending moment at point B

A:

Q: MC hinge 900 km. cable

A:

Q: 2.62 Calculate the beam reactions at supports A, C, and D. Draw all appropriate FBDS. 300# A 200#…

A: Free body diagram of the member AB.

Q: E 100 kN- 3 m 200 kN (D 3 m 4 m

A:

Frames

The trusses and frames are the two most important structural members of civil engineering. Trusses are the interconnection of links and other structural members. The interconnection with other members makes the system behave as a single member that supports and transfers loads. Trusses are generally two types, plane truss, and space truss. Frames on the other hand form the skeleton of any building construction. Frames are structures formed by the connection of beams, columns, slabs, and joists. These members provide the building with the required structural support.