InClass6_Week10

plz solve it within 30-40 mins I'll give you multiple upvote

Solve show all steps and solution. Energy systems engineering

please read everything properly... Take 3 4 5 hrs but solve full accurate drawing on bond paper don't use chat gpt etc okk.... Not old solutions just new solve

Alert for not submit AI generated answer. I need unique and correct answer. Don't try to copy from anywhere. Do not give answer in image formet and hand writing

Please Asap

Mech. Engg. Dept. 4th year 2022-2023 Solar Energy Spring course MEC364 Dr. Mahmoud U. Jasim Review/Recap Sheet Q1- Answer with true or false and rewrite the false statements completely in correct form, otherwise no mark will be put on the false statements. 1 2 To represent a location on earth surface you need to define its altitude and longitude angles. 3 Solar zenith and solar incidence angles have the same value for horizontal surface. At sunset time the value of solar altitude angle is maximum. 4 The angle which represents the inclination of a given surface is the zenith angle 5 6 7 8 When the absolute value of sun-wall azimuth angle exceeds 90' this means that the sun rays are reaching the receiving plane. The solar irradiance and the solar irradiation have the same physical meaning. In the case of clear sky weather, the beam solar irradiation on a horizontal surface is less than the diffused irradiation. The total solar radiation received by a tilted surface is the same as that…

Help!!! Please answer all Correctly!!! Please

Case Study: Paula’s Pain Paula has worked for Brindle Corporation for 3 years.  During this time, she has worked as a machine operator/cell leader in various work cells.  Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel.  These tubes get a hole punched in them, a flange welded on, and burrs ground off.  The pipe then gets placed into a gage to check that it was made correctly.  (The tubes weigh about six pounds.) Paula has been performing the welding operation.  She leans into the machine and loads the part into a fixture then positions the flange.  Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position…

Help!!! Please answer all Correctly!!! Please

Vo) 1 0.00 LTE2 KB/s 4G 4G 3:43 64 + IIl yr RAC - Tes... / Government College of Engineering, Salem-11 Department of Mechanical Engineering Sub Code:16PTME303 Sub Name: Refrigeration and Air Conditioning UNIT TEST –I Date: 23/092020 Class: B.E PT Mechanical Engineering Marks:50 Semester: III Duration:90 min PART – A Q. No Question M BT CO L 1 Draw T-S and P-h diagram for Vapour compression cycle with vapour wet after compression. 1 1-F Define ton of refrigeration. 2 1-F 1 Determine the COP of a refrigerating machine working on a reversed Carnot cycle operates between 310K and 250K. 3 2 1- 1 A 4 2 1- 2 Classify the refrigerant evaporators A 2 1- 2 State the merits and demerits of air-refrigeration system. U PART- B M BT CO A vapour compression refrigerator circulates 4.5 kg of NH3 per hour, | 15 condensation take place at 30°C and evaporation at -15°C. There is no under-cooling of the refrigerant. The temperature after isentropic compression is 75°C and specific heat of superheated…

1. What are the properties of natural gas? 2. Outline the difference between non associate and associated gas i need clear ans and solve very very fast in 20 min and thank you | DYBALA

O Week 2- 20527 22110L x a MasteringEngineering Mastering x M Inbox (10,309) - usmikail@gmail x a Product Detail Page a Central Service Technical Manual x O 21) YouTube i session.masteringengineering.com/myct/itemView?assignmentProblemiD=12443395&offset=next KHW 1 Problem 12.3 6 of 16 I Review A particle travels along a straight line with a velocity v = (12 – 3t2) m/s, where t is in seconds. When t = 1 s, the particle is located 10 m to the left of the origin. Express your answer to three significant figures and include the appropriate units. As = 437 Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining Part C Determine the distance the particle travels during the time period given in previous part. Express your answer to three significant figures and include the appropriate units. ? ST = Value Units

cc 030 BY NO SA 2020 Joe Graber h a) How far down the slope will they land?r= Vo A (tiny) snowboarder leaves a h = 3 m jump traveling with a velocity of Vo = 10 m/s at an angle of 0 = 25° from the horizontal. They land on a slope that is at an angle of = 10°. b) How long will they be in the air? t = A S m

The free body diagram must be drawn , its mandatory. Don't use chatgpt

Q-1A) Identify if TRUE or FALSE, give an explanation for the FALSE ones only). a. If a homogenous piece of rock is cut into two pieces, then each one will have the same formation factor. h Micro-resistivity log can be used in oil-based mud and water-based mud systems. L. In a water bearing formation, Ro is equal to the Rt. d. A high GR value always indicates the presence of shale. e One of the most important application of the SP log is to measure the formation permeability. L Caliper log shows a smaller reading that the bit size for evaporite (Salt) layers. g. If the micro-Inverse and micro-Normal logs exhibit positive separation, the permeability of the formation is small. b. A reverse/positive SP deflection occurs when Rmf< Rw. i Water Saturation is defined by the ratio of water volume to the bulk volume of a rock. i The higher formation porosity, the larger invasion diameter. k. Induction log measures the formation resistivity. L Well-logging measurements are recorded while puling…