Unit 7 Quiz

MULTIPLE CHOICE -The answer is one of the options below please solve carefully and circle the correct option Please write clear .

Do not give answer in image and hand writing

Oz Lawn Care Inc. manufactures and assembles lawnmowers that are shipped to dealers throughout the United States and Canada. Two different procedures have been proposed for mounting the engine on the frame of the lawnmower. PB (Minutes) UPB (Minutes )345798632 5 Is there a difference in the methods' mean time to mount the engines on the frames of the lawnmowers? The answer must be in handwriting. Please write your answer using a ball - point pen on plain paper. Submit your homework by uploading it to the canvas. Good Luck!

University of Babylon College of Engineering\Al-Musayab Automobile Engineering Department Final Examination/1st Attempt جامعة بابل Subject: I. C. Engines I Maximum Time: 3 Hours Class: 3rd Date: / / 2023 Answer 07 of the following questions (First Semester) 2022/2023 (1) Choose the correct answer for eight only from below 1- Indicator diagram shows for one complete revolution of crank Maximum mark: 50 Deg. a) variation of kinetic heat in the cylinder. b) variation of pressure head in the cylinder c) variation of kinetic and pressure heat in the cylinder. d) none of the above. 2- A carburetor is used to supply (a) petrol, air and lubricating oil (b) air and diesel (e) petrol and lubricating oil (d) petrol and air. 3- In a four stroke cycle petrol engine, the charge is compressed when a) inlet valve is closed. b) exit valve is closed. c) both inlet and exit valves are closed. d) both inlet and exit valves are open. (8 deg.) 4- For an engine operating on air standard Otto cycle, the…

University of Babylon College of Engineering\Al-Musayab Automobile Engineering Department Final Examination/1st Attempt جامعة بابل Subject: I. C. Engines I Maximum Time: 3 Hours Class: 3rd Date: / / 2023 Answer 07 of the following questions (First Semester) 2022/2023 (1) Choose the correct answer for eight only from below 1- Indicator diagram shows for one complete revolution of crank Maximum mark: 50 Deg. a) variation of kinetic heat in the cylinder. b) variation of pressure head in the cylinder c) variation of kinetic and pressure heat in the cylinder. d) none of the above. 2- A carburetor is used to supply (a) petrol, air and lubricating oil (b) air and diesel (e) petrol and lubricating oil (d) petrol and air. 3- In a four stroke cycle petrol engine, the charge is compressed when a) inlet valve is closed. b) exit valve is closed. c) both inlet and exit valves are closed. d) both inlet and exit valves are open. (8 deg.) 4- For an engine operating on air standard Otto cycle, the…

New York Building Corporation uses the critical path method to monitor construction jobs. The company is currently 2 weeks behind schedule on Job #181, which is subject to a P10,500 per week completion penalty. Path A-B-C-F-G-H-I has a normal completion time of 20 weeks, and critical path A-D-E-F-G-H-I has a normal completion time of 22 weeks. The following activities can be crashed.                Activities                         Cost to Crash 1 Week                 Cost to Crash 2 Weeks                    BC                                     P  8,000                                          P15,000                    DE                                       10,000                                            19,600                    EF                                         8,800                                             19,500         REQUIRED: 1. New York Building desires to reduce the normal completion time Job #181 and, at the same time, report the highest possible income…

Handwritten solution required. Strictly don't use chatgpt. If you use chatgpt ,I will report the answer for sure. Mechanical engineering dynamics.

The answers to this question s wasn't properly given, I need expert handwritten solutions

age) #5: A certain rocket engine has a temperature when in use of approximately 182°C. If left to cool in a 20°C room for 24 hours, it is known that the engine temperature will be 26°C. If the engine obeys "Newton's Law of Cooling", how long in hours would the engine have cool after use before it reaches 74°C? #5: answer correct to 2 decimals Save Your work has been saved!_(Back to Admin Page)

Posted below is a picture of a data table and a diagram of an experiment. In the experiment you rolled a marble down a ruler ramp off the end of a coffee table to observe projectiles and conservation of energy. You do 3 trials for each initial height. Each height is measured in meters. h= initial height of marble off of table Y= height of table off floor X= horizontal distance marble goes from edge of table to where it strikes the floor a) use the table to find information you need to solve for theoretical range and % of error in measured range.

What’s the the answer please

Hartley Electronics, Inc., in Nashville, producesshort runs of custom airwave scanners for the defense industry.The owner, Janet Hartley, has asked you to reduce inventory byintroducing a kanban system. After several hours of analysis, youdevelop the following data for scanner connectors used in onework cell. How many kanbans do you need for this connector?Daily demand 1,000 connectorsLead time 2 daysSafety stock 12 dayKanban size 500 connectors

Per Bartleby honor code only 3 subparts of a question can be answered per submission. I have submitted 10, 11, 12, and 13 previously. Please answer 14, 15, 16

Please give me the answers for this i been looking at this for a hour and my head hurts

please hand written solution  please hand written solution  please hand written solution

It is currently day 10 in the production calendar of the Machine Shop. Three orders(A, B, and C) are to be processed at a particular machine tool. The orders arrived in thesequence A-B-C. The table below indicates the process time remaining and productioncalendar due date for each order. Determine the sequence of the orders that would bescheduled using the following priority control rules: (a) first-come-first-serve, (b) earliest due date, (c) shortest processing time, (d) least slack time, and (e) critical ratio

9.5.29 Question He Find the work W done by a force of 3 pounds acting in the direction 45 to the horizontal in moving an object 7 feet from (0 0) to (7,0) . foot-pounds Round to the nearest whole number as needed) %3D 用 Enter your answer in the answer box and then click Check Answer All parts showing School a for nk6xemh85d.execute-api.us-east-1.amazonaws.com... EX