MCCG150 Classification Coding Scenario w2

Question 2 You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the…

Access Pearson Mastering Engineering Back to my courses Course Home Course Home Scores ■Review Next >

Please give me the answers for this i been looking at this for a hour and my head hurts

please help solve A-F. thank you You are an engineer working on a project and your prototype has failed prematurely. You question whether or not a key component of the prototype was manufactured with the correct material. There are two way to check for the material properties. The first way is to have a material certification done to confirm the exact material composition. This will take some time. The second method to confirm the material properties is to make an ASTM test sample and test for the material properties. This tensile test was completed on a test sample with an initial diameter of .501” and an initial length of 2”. The Load-Deflection data for this tensile test is below. Use this data to answer the first set of questions on the Final Exam in eLearning. A. Determine the Ultimate Tensile Strength B. Determine the 0.2% Offset Yield Strength C. Determine the value of the Proportional Limit D. Determine the Modulus of Elasticity E. Determine the Strain at Yield F. Calculate %…

AMNT 280 Assignments 1-4 Media Presentation Categories Of Reciprocating Engines   Develop a Media Presentation develop a power point media presentation Presentation will require researching a module specific topic For this activity you will research the four categories of reciprocating engines In your presentation address the following: 1 Research the four different types of reciprocating engines2 Provide an overview of the design, construction, and firing order of each engine 3 Provide research concerning which air frame used the engine Presentation Guidelines Note:This information applies to all Media Presentation activities and will not be repeated Present your research material in the format of a written document (Introduction, body, and conclusion) Presentation requirements consist of 5-7 slides with a balance of both bullet text information and images; does not include the title or reference slide APA formatting and structural guidelines apply  Additional information…

Please answer the 4th question

I need parts 8, 9, and 10 answered. Number 1 is an example of how it should be answered. NOTE: Read the instructions, no where does it say any drawing is required. It is really frustrating when I wait all this time for an answer to a question and some tutor does even read the instructions and just declines it...its ridicilous.

Access Pearson Mastering Engineering Back to my courses Course Home Course Home Scores

I need answers to questions 7, 8, and 9 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.

University of Babylon Collage of Engineering\Al-Musayab Department of Automobile Engineering Under Grad/Third stage Notes: 1-Attempt Four Questions. 2- Q4 Must be Answered 3-Assume any missing data. 4 تسلم الأسئلة بعد الامتحان مع الدفتر Subject: Mechanical Element Design I Date: 2022\01\25 2022-2023 Time: Three Hours Course 1 Attempt 1 Q1/ Design a thin cylindrical pressure tank (pressure vessel) with hemispherical ends to the automotive industry, shown in figure I below. Design for an infinite life by finding the appropriate thickness of the vessel to carry a sinusoidal pressure varied from {(-0.1) to (6) Mpa}. The vessel is made from Stainless Steel Alloy-Type 316 sheet annealed. The operating temperature is 80 C° and the dimeter of the cylinder is 36 cm. use a safety factor of 1.8. Fig. 1 (15 Marks) Q2/ Answer the following: 1- Derive the design equation for the direct evaluation of the diameter of a shaft to a desired fatigue safety factor, if the shaft subjected to both fluctuated…

I need parts 1, 2, and 3 answered pertaining to the print provided. NOTE: If you refuse to answers all 3 parts and insist on wasting my question, then just leave it for someone else to answer. I've never had an issue until recently one single tutor just refuses to even read the instructions of the question and just denies it for a false reasons or drags on 1 part into multiple parts for no reason.

Can someone please help me to answer all of the following questions thank you!!

I need problems 6 and 7 solved.  I got it solved on 2 different occasions and it is not worded correctly. NOTE: Problem 1 is an example of how it should be answered. Below are 2 seperate links to same question asked and once again it was not answered correctly. 1. https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857 2. https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/bd5390f0-3eb6-41ff-81e2-8675809dfab1

I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)?   https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857

Case Study – The New Engineer   Jeff was just hired by GSI, Inc. to be their Environmental and Safety Coordinator.  This is Jeff's first position after completing his engineering degree.  He had taken a course in safety engineering as part of his studies and felt confident that he could handle the job.   Management at GSI, Inc. has assured him that they are committed to maintaining a safe workplace.  They have never had an individual dedicated to this task full-time.  They will implement his recommendations if he can justify them.   As Jeff begins to get familiar with the operations, he spends considerable time on the production floor.  He notices workers clean their tools before break with a liquid from an unmarked 55-gallon drum.  They also use this liquid to clean residue from their skin.  They use paper towels to dry their tools and hands, throw these towels in the trash, and head to the break room for a snack and/or smoke.   In talking with the workers, Jeff learns of some of…

Case Study – The New Engineer   Jeff was just hired by GSI, Inc. to be their Environmental and Safety Coordinator.  This is Jeff's first position after completing his engineering degree.  He had taken a course in safety engineering as part of his studies and felt confident that he could handle the job.   Management at GSI, Inc. has assured him that they are committed to maintaining a safe workplace.  They have never had an individual dedicated to this task full-time.  They will implement his recommendations if he can justify them.   As Jeff begins to get familiar with the operations, he spends considerable time on the production floor.  He notices workers clean their tools before break with a liquid from an unmarked 55-gallon drum.  They also use this liquid to clean residue from their skin.  They use paper towels to dry their tools and hands, throw these towels in the trash, and head to the break room for a snack and/or smoke.   In talking with the workers, Jeff learns of some of…

pls help me with this one :(

Please double check before rejecting this question. If it needs to be rejected, please explain why as I cannot see how this is a breach of the honor code. This is a questions from the previous year's exam at my university in Engineering Science. I have submitted a solution given to us for study purposes as proof that I will not be graded on this assessment. In this solution, the formula (2gh)1/2 is used to find the solution, but I am on familliar with Bernoulli's Principle (P=1/2pv^2+pgh), and I was not able to find a solution using this. My solution incurred an error when I found that I had two unkown variables left that I could not break down in any meaningful way. (Velocity being the desired variable, Pressure being the problematic variable). Pressure = Force x Area, but I don't know enough about the dimensions of the tank or tap to be able to understand this. Thank you for your help.

A Team of Engineers asked for an internal combustion engine to use it in a designed car. Your role is to describe the operation sequence of different types of available engines, explain their mechanical efficiency, and deliver a detailed technical report to show your approach in solving and discussing the following tasks and issues.  You must follow the following steps to help the team:  STEP 1  Describe the operational sequence of four-stroke spark ignition and four-stroke compression ignition engines with the aid of sketches by constructing simple sketch representing the operation and plotting the P-V diagrams for each process during the cycle to show the following:  The input and output heat and net output work The expansion and compression strokes The air-fuel mixture intake and exhaust gasses The spark plug when it is in the active mode The complete cycle of ideal Otto and Diesel cycles that shows the input and output heat and net output work. STEP 2  Explain the mechanical…

I need answers to problems 7, 8, and 9.  NOTE: Please stop wasting my time and yours by rejecting my question because it DOES NOT REQUIRE YOU TO DRAW anything at all. They are simple questions pertaining to the print provided. READ THE INSTRUCTIONS of the assignment before you just reject it for a FALSE reason or leave it for someone to answer that actually wants to do their job. Thanks.

You are assigned as the head of the engineering team to work on selecting the right-sized blower that will go on your new line of hybrid vehicles.The fan circulates the warm air on the inside of the windshield to stop condensation of water vapor and allow for maximum visibility during wintertime (see images). You have been provided with some info. and are asked to pick from the bottom table, the right model number(s) that will satisfy the requirement. Your car is equipped with a fan blower setting that allow you to choose between speeds 0, 1,2 and 3. Variation of the convection heat transfer coefficient is dependent upon multiple factors, including the size and the blower configuration.You can only use the following parameters:

Please give a complete solution in Handwritten format. Strictly don't use chatgpt,I need correct answer. Engineering dynamics

Instrumentation & Measurements This homework measures your capability to design/analyze various components/variables of ameasurement system based on what you have studied. Question is Attached in image. Thank you.

I need GF,CF,CD asap please

I need answers to questions 1, 2, and 3 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.

Last person got every single question wrong and didn't include units. Please help.

You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the Ti-6Al-4V…

Chapter 12 - Lecture Notes.pptx: (MAE 272-01) (SP25) DY... Scores

I need help with this before tomorrow’s exam if I can get all needed calculations please

I need answers to questions 13, 14, and 15 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.