HW. 1

1/8 2015 Cengage Learning Refer to the drawing Bracket below. 1. Explain fully the meaning of each of the welding symbols used on the drawing. 2. How far apart (in degrees) are the equally spaced drilled holes? 3. Define the dimension 3" XS BI Pipe. 4. How many parts does this bracket consist of? 5. What plate size is used? 6. What type of section is represented by section A-A? 0.250 DRILLTHRU SIX HOLES EQUALLY SPACED 23° CYLINDRICAL PLATE 1" STD 8 PIPE E. A 3" XS BI PIPE 01013" 3" 8. $12! B 3. 32 25" 337 5" 2" HH !..6 D. BRACKET

answer a & b. Please show all your work!!

Alert for not submit AI generated answer. I need unique and correct answer. Don't try to copy from anywhere. Do not give answer in image formet and hand writing

How many cutting-plane lines are shown on this print?

Please solve d) and e) only. Thank you.

4.41 in.8.82 in.14 in.22.82 in.

I need parts 2 and 3 answered please and thank you.

University of Babylon College of Engineering\Al-Musayab Automobile Engineering Department Final Examination/1st Attempt جامعة بابل Subject: I. C. Engines I Maximum Time: 3 Hours Class: 3rd Date: / / 2023 Answer 07 of the following questions (First Semester) 2022/2023 (1) Choose the correct answer for eight only from below 1- Indicator diagram shows for one complete revolution of crank Maximum mark: 50 Deg. a) variation of kinetic heat in the cylinder. b) variation of pressure head in the cylinder c) variation of kinetic and pressure heat in the cylinder. d) none of the above. 2- A carburetor is used to supply (a) petrol, air and lubricating oil (b) air and diesel (e) petrol and lubricating oil (d) petrol and air. 3- In a four stroke cycle petrol engine, the charge is compressed when a) inlet valve is closed. b) exit valve is closed. c) both inlet and exit valves are closed. d) both inlet and exit valves are open. (8 deg.) 4- For an engine operating on air standard Otto cycle, the…

University of Babylon College of Engineering\Al-Musayab Automobile Engineering Department Final Examination/1st Attempt جامعة بابل Subject: I. C. Engines I Maximum Time: 3 Hours Class: 3rd Date: / / 2023 Answer 07 of the following questions (First Semester) 2022/2023 (1) Choose the correct answer for eight only from below 1- Indicator diagram shows for one complete revolution of crank Maximum mark: 50 Deg. a) variation of kinetic heat in the cylinder. b) variation of pressure head in the cylinder c) variation of kinetic and pressure heat in the cylinder. d) none of the above. 2- A carburetor is used to supply (a) petrol, air and lubricating oil (b) air and diesel (e) petrol and lubricating oil (d) petrol and air. 3- In a four stroke cycle petrol engine, the charge is compressed when a) inlet valve is closed. b) exit valve is closed. c) both inlet and exit valves are closed. d) both inlet and exit valves are open. (8 deg.) 4- For an engine operating on air standard Otto cycle, the…

Please show detailed solution in a handwritten format. Don't use chatgpt. Torque and Maximum shear stress need to be determined

I need these two parts answered (Multiple Choice). If you can not answer all two parts please leave it for another tutor to answer. Thank you.   What tolerance is specified for the depth of the groove featured in the enlarged detail? (Multiple Choice)a. .002'b. .004'c. .005'd. .010' What was the main focus of the last revision of this print? (Multiple Choice)a. Paint coatingsb. Heat treatc. Assembly adhesivesd. Geometric tolerancing

Drilling and Completion Engineering II An exploration well is to be drilled to a total depth of 19000 ft, relevant data are as follows: Safety factors for collapse and burst are 0.9 and 1.05 respectively. Design suitable casing strings for the given hole sizes, taking into consideration the available casing grades and the maximum expected pressures. The answer by hand written in a clear way

A ballistic pendulum consists of a 3.3-kg wooden block originally at rest, 0 = 0°. When a 2-g bullet strikes and becomes embedded in it, it is observed that the block swings upward to a maximum angle of 0 = 6°. (Figure 1) Figure 99 F Sunny 0 1.25 m 0 1.25 m 1 of 1

Select all true statements. O To obtain a mining lease, the holder of a mining claim must absolutely acquire surface rights. | Mechanized stripping is used to expose the bedrock linearly to test the geological unit of interest on its full width, perpendicular to its contact with the surrounding units. The apparent length of a mineralized zone of interest is always shorter than its true width. Upon reaching commercial production, the purchaser of a mineral exploration property can pay a certain amount to the seller in exchange for a reduction of the percentage of the Net Smelter Return (NSR) retained by the seller.

What is the tolerance on the shaft 'S'? What is the tolerane on the hole, T? What is the minimum clearance parts 'S' anbd 'T'? Please answer question 17 and 18 attached in photos.     (usually i will not submit more then 2 questions but due to the fact it is so simple, thank you, be safe and healthy )